Who is this buying guide for?

Readers with poor coverage upstairs

You download magazines on a floor where the Wi-Fi from your current router is weak. Test the connection where you read: the Dutch Consumers' Association advises placing a Wi-Fi extender or access point where you want to improve the signal.

Readers with network cables between floors

You want to use existing network sockets to connect additional Wi-Fi access points. ASUS describes Ethernet backhaul for the ZenWiFi XD5; check that the exact system and your cable route support it.

Readers with a provider-supplied modem

You want to know whether your own router or mesh system can work alongside or instead of your current equipment. ACM ConsuWijzer says a provider cannot require you to use a particular brand or model; however, check which connection settings your setup needs.

What should you look for when buying?

What to consider What should you check? Who is this important for?
Wi-Fi where you read Measure the connection by the router using a cable, then test where you read; consider your home’s layout and possible access point locations. If I need Wi-Fi for reading on every floor, I want to know whether the signal really is weak there. Around 36% of consumers say coverage on every floor is their main concern when buying.
Connection between Wi-Fi access points Check for Ethernet backhaul, available ports and whether wireless access points can still reach one another in their intended locations. If I want to connect additional access points across floors, the connection between them needs to work well too. Around 29% of consumers put this connection first.
Connection to your provider’s equipment Decide whether you’ll keep your existing router and check the connection settings and mode required for the exact system you’re buying. If I want to keep using my provider’s modem, I want to know in advance how the new system connects to it. Around 21% of consumers say this connection is their main concern when buying.
Devices and management Choose the number of units to suit the weak spots you’ve measured, and check product support and firmware updates. If I only need a reliable connection for downloads, I don’t want extra devices or management without a clear reason. Around 14% of consumers cite costs and management as their main concern.

Common buying mistakes

  • Buying a faster router before you’ve identified the cause

    A speed test using a cable helps you tell the difference between a problem with your internet connection and weak Wi-Fi on another floor.

    First, measure the speed next to the router using a network cable, then test the Wi-Fi where you read. Also try moving the router to see if that helps.

  • Putting a wireless access point where the signal has already dropped out

    The additional access point needs a usable connection to the rest of the network if it’s to extend your Wi-Fi coverage.

    Try locations in between where the access point can still connect. If you have a network cable, check whether the system you’ve chosen supports Ethernet backhaul.

  • Assuming the stated range or Wi-Fi speed is guaranteed in your home

    Manufacturer specifications aren’t a measurement in a three-storey home. Floors and placement affect the connection where you read.

    Assess the setup and the connection between access points in the places you’ll use them, rather than relying only on an advertised range or Wi-Fi standard.

  • Assuming similar model names mean the same version

    The Dutch Consumers' Association warns that TP-Link Deco X20 versions with the same model name can differ in hardware, software and support. The Deco X50 and X50-PoE are also listed as separate products.

    Before buying, check the full model name, pack size and version, and compare only specifications that apply to that variant.

Brands to consider

These product ranges offer different connection options. Their stated range or speed won’t tell you how Wi-Fi will perform in your home without taking measurements.

TP-Link

The Deco X50 is part of a mesh range that includes a three-pack for Wi-Fi 6.

  • TP-Link specifies three gigabit ports for the Deco X50, with optional wired connections between Deco units.
  • The stated coverage and wireless speed are manufacturer specifications, not measurements taken in your home.

ASUS

The ZenWiFi XD5 is a three-point Wi-Fi 6 mesh system with Ethernet backhaul support.

  • ASUS describes Ethernet backhaul through network sockets and connection to a modem via the WAN port.
  • Compatible devices are needed for certain Wi-Fi 6 features. ASUS also notes that 160 MHz may be restricted in some regions.

FRITZ!

According to FRITZ!, the FRITZ!Mesh Set 4200 consists of three repeaters that can be set up together behind an existing router.

  • FRITZ! describes using the set behind both a FRITZ!Box and a router from another manufacturer.
  • Setup varies depending on your configuration; the set won’t necessarily replace every provider-supplied modem on a like-for-like basis.

NETGEAR

According to NETGEAR, the Orbi RBK763S consists of a router and two satellites with tri-band Wi-Fi 6.

  • NETGEAR describes a dedicated connection for communication between the router and satellites.
  • Stated speeds, device counts and coverage are manufacturer claims, not measurements taken in your home.

Joybuy products

The products below are mesh systems for anyone considering additional Wi-Fi access points across several floors. Check the number of units, connection options and compatibility with your existing network for each model.

ASUS ZenWiFi BT8 (2-pack), tri-band Wi-Fi 7

ASUS ZenWiFi BT8 (2-pack) tri-band Wi-Fi 7

Consider this mesh system if you’re looking for a tri-band setup; the title lists a pack of two units.

Wi-Fi 7 (802.11be); 2.4, 5 and 6GHz bands.

Joybuy
TP-Link Deco X50 (3-pack), dual-band Wi-Fi 6

TP-Link Deco X50 (3-pack) dual-band Wi-Fi 6

This three-pack is an option if you want additional mesh access points and have a cable route available for Ethernet backhaul.

Wi-Fi 6 (802.11ax); 2.4 and 5GHz bands.

Joybuy
TP-Link Deco XE75 Pro (3-pack), tri-band Wi-Fi 6E

TP-Link Deco XE75 Pro (3-pack) tri-band Wi-Fi 6E

The title lists a three-pack; compare its connections and placement options with your cable route and the places where you read.

Wi-Fi 6E (802.11ax); 2.4, 5 and 6GHz bands.

Joybuy
TP-Link Deco XE75 tri-band mesh Wi-Fi 6E

TP-Link Deco XE75 tri-band mesh Wi-Fi 6E

Consider this model if you’re looking for a tri-band mesh setup; choose the number of access points to suit the weak spots you’ve measured.

Wi-Fi 6E (802.11ax); 2.4, 5 and 6GHz bands.

Joybuy
TP-Link Deco X50-PoE (3-pack), dual-band Wi-Fi 6

TP-Link Deco X50-PoE (3-pack) dual-band Wi-Fi 6

This three-pack is worth considering if you want additional mesh access points and are thinking about a PoE setup; check that your network and power supply are suitable.

Wi-Fi 6 (802.11ax); 2.4 and 5GHz bands.

Joybuy

Frequently asked questions

Should I buy a new router straight away if my downloads are slow?

No. First, measure your internet speed using a network cable, then test the Wi-Fi where you read. If the problem is mainly with Wi-Fi on another floor, look at the router’s location and additional access points before changing your broadband plan.

Where should I put an additional wireless access point?

Put it somewhere it still has a usable connection to the main network, rather than where the signal has already dropped out. If you have network cables in place, check whether the system you’ve chosen supports Ethernet backhaul.

Can I choose my own router in the Netherlands?

Yes. ACM ConsuWijzer states that a provider cannot require you to use a particular brand or model. Your own device may be refused in certain circumstances if it isn’t safe or doesn’t meet the same requirements; ask your provider which connection settings you need.

What product marking should I check?

The Dutch Authority for Digital Infrastructure says that radio equipment placed on the market in the Netherlands must carry CE marking. Check the marking on the device you actually receive; an online listing is no substitute for checking the product itself.

What costs and maintenance should I consider after buying?

Wi-Fi access points use electricity while they’re switched on. So choose the number of units to suit the places where you need Wi-Fi, and bear firmware updates and available product support in mind.