Presenting behind thick walls
You want to share a presentation in a remote room and first need to check whether the local network is reliably available there. The Consumentenbond notes that walls and ceilings can disrupt Wi-Fi signals.
First, test the Wi-Fi where you’ll be presenting and check whether the problem is with your local connection or your internet service. If you can run an Ethernet cable to the room, a wired access point or mesh node may be a good option. Without a cable, wireless mesh depends on the connection between the nodes, while powerline depends on your home’s electrical wiring. A higher advertised top speed alone won’t guarantee coverage through thick walls.
You want to share a presentation in a remote room and first need to check whether the local network is reliably available there. The Consumentenbond notes that walls and ceilings can disrupt Wi-Fi signals.
You can connect a Wi-Fi point by cable near the presentation area and are looking for a system with suitable Ethernet backhaul or access point mode. TP-Link describes Ethernet backhaul as a way to connect compatible Deco units by cable.
You need to choose between wireless mesh nodes with a usable connection between them and a powerline solution that you can test using the sockets in your home.
Best if: a more central or higher position for the router could improve the connection to the presentation area.
Bear in mind: moving it may require a longer cable, and it won’t necessarily solve the problem if a wall continues to block the signal.
Best if: an Ethernet cable reaches the room and you need local Wi-Fi there.
Bear in mind: you’ll need a working cable or network connection; the correct operating mode varies by model.
Best if: there’s no cable, but the planned mesh nodes can still establish a usable wireless connection with each other.
Bear in mind: a node placed in a dead zone still needs its own connection to the network.
Best if: running a cable isn’t practical and testing the sockets you plan to use gives you a usable connection.
Bear in mind: performance depends on your home’s electrical wiring.
| What to consider | What should you check? | Who is this most relevant to? |
|---|---|---|
| Coverage where you’ll be presenting | Test the connection where you’ll be presenting and see where a Wi-Fi point could go; don’t treat advertised coverage areas as a guarantee. | If I’m presenting behind thick walls, I want to know whether Wi-Fi reaches the room before I buy equipment. Around 36% of consumers put usable coverage in that spot first. |
| Connection between the nodes | Check whether the exact model supports Ethernet backhaul and test powerline using the sockets you plan to use. | If I add another Wi-Fi point, I want it to have a reliable connection to the network itself. Around 29% of consumers prioritise the connection between nodes. |
| Sharing method and receiver | Decide whether you’ll use Google Cast, Miracast or another method, and check the settings and compatibility of both the sending and receiving devices. | If I’m sending a presentation to a screen, I want to know whether my devices can communicate using the method I’ve chosen. Around 21% of consumers prioritise this compatibility. |
| Connection and aftercare | Check the operating mode, connections and CE marking on the specific device; also look into what firmware support is available. | If I want to keep using my existing router, I want to know how the new device connects to it and what to look out for when buying. Around 14% of consumers prioritise connectivity and aftercare. |
Walls and ceilings can weaken the signal. An advertised speed or coverage area doesn’t tell you how good the connection will be where you’re presenting.
Test the connection there before you buy, then decide whether to move the router or add another Wi-Fi point.
If coverage is still poor, you may need another Wi-Fi point or a cable after all.
The extra node still needs a usable connection to the rest of the network. Otherwise, it won’t be able to provide a good connection to the presentation area.
Test the planned location and, if possible, use Ethernet backhaul supported by the model.
An advertised powerline speed isn’t a measurement taken using the sockets in your home.
Test the adapters where you intend to use them before relying on that connection for a presentation.
A device can have internet access without being able to find the presentation receiver on the local network. Google Cast and Miracast each have their own requirements.
First, check which sharing method you’re using, then review the relevant network settings and receiver support.
According to TP-Link, the Deco X55 offers Wi-Fi 6 mesh with optional Ethernet backhaul, while the Deco PX50 combines Wi-Fi with G.hn powerline.
ASUS describes the ZenWiFi XD5 as a mesh option with Ethernet backhaul and settings for using one network name or separate names.
The Devolo Magic 2 WiFi 6 next combines powerline with a local Wi-Fi point for situations where running a cable isn’t practical.
The Consumentenbond describes the Orbi 770 RBE773 as a set of three Wi-Fi 7 points.
This selection includes mesh sets and a wired access point for Wi-Fi where you’ll be presenting. The right option depends, among other things, on whether an Ethernet cable is available and how well the mesh nodes connect to each other.
No image available
A mesh set of two units with wired and wireless backhaul. A good option if you want to choose between the two ways of connecting the units.
Wi-Fi 7; Ethernet ports on each unit, including 10 Gbps and 2.5 Gbps ports.
No image available
A mesh set of two units for anyone considering a wireless mesh setup; check that the planned locations allow the units to establish a usable connection with each other.
Tri-band: 2.4, 5 and 6 GHz; AiMesh integration with compatible ASUS routers.
No image available
A mesh option with wired backhaul for anyone who can connect a working Ethernet cable to the node in question.
Dual-band: 2.4 and 5 GHz. Wired backhaul requires an Ethernet cable to the mesh node.
No image available
A wired access point for adding local Wi-Fi in a place where Ethernet is available.
Wi-Fi 6; one Ethernet port and PoE power. An Ethernet connection to the device is required.
No image available
A mesh set with three units for anyone who wants Wi-Fi in several areas; the number of units alone doesn’t guarantee coverage through thick walls.
Tri-band Wi-Fi 6E; three Ethernet ports on each unit.
No. First, check the connection where you’ll be presenting and try moving the router to a better position. If possible, compare it with a wired test of your internet connection to tell an internet problem apart from a local Wi-Fi issue. The Consumentenbond also recommends considering where you place your Wi-Fi modem.
It depends on the operating mode and model. For Deco in router mode, TP-Link describes connecting a satellite via the LAN port on the main Deco or a switch connected to it. Check in the app that Ethernet backhaul is active.
First, check the sharing method and receiver compatibility. For Google Cast, Google recommends using the same Wi-Fi network and disabling AP or client isolation; for Miracast, the receiver must support Miracast.
Yes. According to ACM ConsuWijzer, you’re free to use your own router. If necessary, ask your provider for the settings for a direct connection and check the CE marking on the specific device; the RDI states that this marking is compulsory for equipment such as Wi-Fi routers.
The RDI states that the CE marking is compulsory for equipment such as Wi-Fi routers. Check the marking on the specific device; a model listing on a product page doesn’t confirm that the device itself carries the marking.