Presenting in the loft
If Wi-Fi is weak in your presentation area on the top floor, check whether a repeater can still receive a usable signal from a position somewhere between there and the router.
If Wi-Fi is weak in one presentation area, a well-placed repeater may be enough. For coverage across several floors, consider a wired access point or a system with multiple mesh nodes. A cable means the connection between your router and Wi-Fi point doesn’t have to be wireless, but check that your equipment supports the mode you want to use. Also test whether your presentation screen can be found: with Google Cast, client isolation and network selection can prevent a connection.
If Wi-Fi is weak in your presentation area on the top floor, check whether a repeater can still receive a usable signal from a position somewhere between there and the router.
If you use different rooms, the connection between your router, Wi-Fi points and devices needs to suit the layout of your home.
As well as having sufficient Wi-Fi coverage, your presentation device and screen receiver need to be able to find each other on the network. Google Cast Help lists network and isolation settings as possible requirements for Google Cast.
Choose this option: if Wi-Fi is weak mainly in one presentation area and the repeater can still receive a good signal from a position somewhere in between.
Bear in mind: the distance and obstacles between the router, repeater and presentation area. Test the connection where you’ll be presenting.
Choose this option: if you can run an Ethernet cable to the floor and connect a Wi-Fi point there.
Bear in mind: the cable and the access point mode supported by your chosen device. TP-Link recommends a wired connection when obstacles make a stable wireless connection difficult.
Choose this option: if you need coverage on different floors and want to stay connected as you move between areas.
Bear in mind: the extra devices you’ll need and their power consumption. Mesh and backhaul features depend on compatible equipment.
For a presentation to work, you need both a reliable connection to the Wi-Fi point and a screen that can be found on the network. For Google Cast, Google Cast Help recommends that the presenting device and receiver are on the intended local network and that AP isolation is turned off.
| Key consideration | What should you check? | Who is this important for? |
|---|---|---|
| Coverage in the presentation area | Check the signal in the presentation area and at a possible midway point. | If I’m presenting upstairs, I want a usable connection right there. Around 33% of consumers prioritise coverage in one presentation area. |
| Connection between floors | Check whether Ethernet is available and verify which access point or backhaul modes the devices support. | If the connection between the router and Wi-Fi point on another floor needs to stay stable, that’s my first concern. Around 27% of consumers give this connection top priority. |
| Finding the screen | For Google Cast, check the local network and client isolation settings on your router and extender. | If I’m presenting wirelessly, I want my device to be able to find the receiver. Around 20% of consumers prioritise screen detection. |
| Setup and use | Check compatibility with your router, the connection mode you want and the stated power consumption. | If I want to keep using my current router and take the power consumption of multiple points into account, setup and ongoing use are my main considerations. Around 20% of consumers prioritise these points. |
A repeater needs a usable connection to the router to extend the network. A spot with almost no router signal isn’t a good starting point.
First, find a midway position where the router signal is still good, then check the connection in the presentation area. If a wireless connection isn’t stable, consider a wired access point.
With Google Cast, AP or client isolation can stop devices from finding each other on the network, even when they have Wi-Fi.
Test the screen technology you’ll be using before your presentation. For Google Cast, check the local network and isolation settings on your router and any extender.
TP-Link says EasyMesh Ethernet backhaul is available only for combinations where both the router and satellite support the feature. Hardware and firmware versions may also matter.
Check the exact devices, versions and connection mode before relying on wired mesh backhaul.
You may need extra compatible equipment or cabling to get the connection you want.
TP-Link describes the RE705X as a Wi-Fi 6 repeater with gigabit Ethernet and access point mode.
FRITZ! describes the FRITZ!Repeater 1200 AX as a Wi-Fi 6 repeater with gigabit LAN.
ASUS describes the RP-AX58 as a repeater with access point mode that can also be used with other routers.
devolo describes the WiFi 6 Repeater 3000 as a repeater that can also be used as an access point.
These are mesh systems with multiple units for Wi-Fi coverage in different areas of your home. Check whether each model supports the connection mode you want; an Ethernet port alone doesn’t guarantee compatible wired mesh backhaul.
No image available
This set of two mesh units is designed to provide coverage in different areas of your home.
The product description lists Ethernet backhaul, multiple Ethernet ports on each unit and setup via the Deco app.
No image available
This set of three units is designed for use in different areas of your home.
Dual-band: 2.4 GHz and 5 GHz; Wi-Fi 5 (802.11ac). The product information lists two Ethernet ports per unit and roaming between Deco units.
No image available
This set of two mesh units is designed to provide coverage in different areas of your home.
Tri-band: 2.4 GHz, 5 GHz and 6 GHz; Wi-Fi 7 (802.11be). The specifications list Ethernet ports supporting 1 and 2.5 Gbit/s.
No image available
This set of three units is designed to provide coverage in different areas of your home.
Dual-band: 2.4 GHz and 5 GHz; Wi-Fi 5 (802.11ac). The product information lists Ethernet ports and roaming between Deco units.
No image available
This set of three mesh units is designed to provide Wi-Fi coverage in different areas of your home.
Dual-band: 2.4 GHz and 5 GHz; Wi-Fi 6 (802.11ax). The product information lists Ethernet ports and optional Ethernet backhaul between Deco units.
Place the repeater between the router and the weak-signal area, somewhere it can still receive a good signal. For areas with obstacles, TP-Link recommends placing it closer to the router. If a wireless connection isn’t stable, it suggests using a wired access point. Then check the connection in the loft; placement advice can’t guarantee results in a particular home.
Check that the presenting device and receiver are on the intended local network and that AP or client isolation is turned off. Google Cast Help lists isolation settings as a possible barrier. This advice applies specifically to Google Cast and doesn’t automatically apply to every presentation technology.
According to the Dutch Digital Infrastructure Inspectorate, radio equipment placed on the market in the EU must meet the applicable requirements and carry the required CE marking. Check the marking and product documentation for the item being offered; a model name or online shop listing alone doesn’t confirm that the item complies.
According to ACM ConsuWijzer, online purchases usually come with a 14-day cooling-off period after delivery, although there are exceptions. In the Netherlands, statutory guarantees also apply for as long as you can reasonably expect the product to last; this doesn’t mean there’s simply one fixed two-year period. Discuss any fault with the seller.