Which setup is right for you?

A hobby room where you can run a network cable

You want to place the Wi-Fi node near the room, so the connection doesn’t have to travel wirelessly through several floors. TP-Link, ASUS and FRITZ! describe solutions with Ethernet backhaul or a wired connection. Check the ports and operating mode of the specific model.

A hobby room with no route for a cable

You’re looking for a wireless connection between the router, any intermediate nodes and the room at the back of the house. The Consumers’ Association (Consumentenbond) recommends placing a Wi-Fi extender in a spot with a stronger signal if reception is weak at the back of the house, for example closer to the centre.

A hobby room behind floors that block the signal

You can’t run a network cable and want to find out whether powerline could be an alternative to a wireless connection between nodes. For its powerline backhaul, TP-Link says compatible units must be plugged directly into wall sockets on the same electrical circuit.

What should you look for?

Wired access point or mesh

Choose this if: you can run a working network cable to your hobby room and need Wi-Fi there.

Bear in mind: you’ll need to run a cable and check the Wi-Fi node’s operating mode; you won’t necessarily need a new main router.

Wireless mesh

Choose this if: running a cable isn’t practical and you can place intermediate nodes where they can still reach one another reliably.

Bear in mind: placing a node where reception is already weak won’t, by itself, fix the connection to the next node.

Powerline mesh

Consider this if: floors or walls interfere with the wireless connection and running a network cable isn’t practical.

Bear in mind: there are requirements for the units and wall sockets you use, and performance in your home isn’t guaranteed.

Repeater with your existing router

Consider this if: you only need to extend coverage to a small area and have a spot with good reception available.

Bear in mind: the repeater still depends on the signal it receives; check compatibility with brand-specific mesh features separately.

What to consider What to look for when buying Who is this important for?
Connection between floors Check whether your chosen solution uses Ethernet backhaul. For powerline, check that the units support the technology and can be plugged directly into suitable wall sockets. If I need Wi-Fi in the room at the back of the house, I want to know how the signal gets there from the router. Around 36% of consumers put the connection to the room first.
Placement without a cable Map out your existing coverage and see whether there’s a spot in between where the incoming signal is still usable; the number of nodes you need varies from home to home. If I can’t run a cable, there still needs to be a suitable place for an intermediate node. Around 29% of consumers put placement and coverage without a cable first.
Connections in the hobby room Count the devices you want to connect by cable and check how many ports will be left in your chosen setup, including when a port is used for backhaul. If my hobby equipment needs a network connection, I want to know how many ports will be left after installation. Around 21% of consumers put connections for their equipment first.
Purchase and management Check whether you can keep your existing router, which operating mode is suitable and whether firmware updates are available for the devices you choose. I’d rather not replace more equipment than necessary, and I need to be able to manage the setup over time. Around 14% of consumers put purchase considerations and ease of management first.

Common buying mistakes

  • Putting an extra node straight in the room at the back

    A wireless node still needs a usable connection to the previous node. If the signal is already weak where you place it, the node can’t restore that connection on its own.

    First, try placing it somewhere in between, with as few obstructions as possible. If the connection isn’t good enough, look into Ethernet or powerline as an alternative route.

    You may need an extra node or a different way to connect.

  • Assuming the speed on the box is the speed you’ll get in your hobby room

    The Consumers’ Association (Consumentenbond) measures differences in range and speed across floors and distances. A Wi-Fi standard or advertised speed alone won’t tell you what connection you’ll get in the place you have in mind.

    Compare the backhaul and placement, and only use test results for the exact version they cover.

  • Assuming powerline devices will work together

    Different powerline technologies don’t automatically work together to provide powerline backhaul. TP-Link says its own backhaul requires compatible units connected to the same electrical circuit.

    Check the full model numbers and supported technology before expanding an existing set.

    You may need to replace incompatible units.

Brands to compare

TP-Link

TP-Link describes the Deco X50 as a mesh system with optional Ethernet backhaul, and the Deco PX50 as a mesh system that, according to the manufacturer, adds G.hn powerline between units.

  • The two models offer different ways of connecting nodes, according to their descriptions.
  • The PX50 powerline feature has requirements for compatible units and your electrical wiring. The stated range or speed won’t predict the results in your hobby room.

ASUS

ASUS describes the ZenWiFi XD5 as a Wi-Fi 6 mesh system that can use Ethernet backhaul if network connections are available.

  • This is a model to compare if you want to place several mesh nodes and can use a wired connection.
  • For the tested white 3-pack, the Consumers’ Association (Consumentenbond) specifically lists hardware model A1. Don’t apply those test results to another version without checking.

FRITZ!

FRITZ! describes the FRITZ!Repeater 3000 AX as an extension for an existing router, either wirelessly or via LAN bridge.

  • According to the manufacturer, this model has two gigabit LAN ports and can be used as a repeater with common routers.
  • According to the manufacturer, integration with FRITZ! mesh requires a suitable FRITZ!Box and software version. General router compatibility doesn’t mean all mesh features work in the same way.

NETGEAR

NETGEAR describes the Orbi RBK763S as a tri-band Wi-Fi 6 set with a router and two satellites.

  • The manufacturer lists dedicated backhaul and gigabit ports for this set.
  • These are product specifications and manufacturer claims, not guaranteed performance in your home. Check whether you need a complete set with several nodes.

Products for extending Wi-Fi

These products include wireless mesh, a Wi-Fi router and powerline adapters for the home. For a wireless device, also check the CE marking on the specific item; according to the Dutch Authority for Digital Infrastructure (Rijksinspectie Digitale Infrastructuur), the correct marking must appear on the device.

TP-Link Deco E4 (3-pack)

TP-Link Deco E4 (3-pack)

A wireless mesh option if you want to place several nodes without running a network cable between them. The product name lists dual-band Wi-Fi on 2.4 and 5 GHz and Wi-Fi 5 (802.11ac).

View on Joybuy
ASUS ZenWiFi BD4

ASUS ZenWiFi BD4

A mesh option to consider if you have a route for a cable between nodes. The product name lists dual-band Wi-Fi 7 (802.11be) on 2.4 and 5 GHz; check that the wired setup suits the route for your cable.

View on Joybuy
TP-LINK TL-WPA7517 KIT powerline adapter set

TP-LINK TL-WPA7517 KIT

A powerline adapter set to consider if you want to extend your network over your home’s electrical wiring. Check that the connections and conditions in your home are suitable; don’t assume it will work with another powerline mesh set.

View on Joybuy
ASUS RT-AX52 AiMesh router

ASUS RT-AX52

A router to consider if you want to replace your existing router and expand your setup later with compatible ASUS AiMesh devices. The product name lists AX1800, Wi-Fi 6 and dual-band on 2.4 and 5 GHz; check which compatible extension devices will work with your setup.

View on Joybuy
TP-Link Deco X50 (3-pack)

TP-Link Deco X50 (3-pack)

A mesh set to consider if you want to place several nodes and can run a network cable between the units. TP-Link describes optional Ethernet backhaul for the Deco X50; the product name lists dual-band Wi-Fi 6 (802.11ax) on 2.4 and 5 GHz.

View on Joybuy

Frequently asked questions

Do I need to replace my existing router?

Not necessarily. If you have a working LAN connection to your hobby room, a suitable device there can act as an access point or LAN bridge. Check the operating mode and connections of the specific model.

Where should I put a wireless intermediate node?

Don’t put it somewhere the incoming signal is already weak. If Wi-Fi is weak at the back of the house, the Consumers’ Association (Consumentenbond) recommends placing a node closer to the centre and minimising obstructions between nodes. Then test reception in your hobby room.

Can I plug Deco PX50 into an extension lead?

For powerline backhaul, TP-Link recommends plugging the units directly into wall sockets on the same electrical circuit. Also check that the Deco units you’re using support the same powerline technology.

Who can help if the device I bought turns out to be faulty?

In the Netherlands, the seller is your point of contact if a product doesn’t meet the standard you’re entitled to expect. The Dutch government (Rijksoverheid) explains your right to a product that works properly; the Consumers’ Association (Consumentenbond) notes that the statutory guarantee doesn’t have a fixed two-year term.

Which marking should I check on a Wi-Fi router in the Netherlands?

According to the Dutch Authority for Digital Infrastructure (Rijksinspectie Digitale Infrastructuur), the correct CE marking must appear on the wireless device. Check the marking on the actual device; a product listing in an online shop doesn’t confirm it.