Who might need a USB headphone DAC?

Listeners without a suitable audio output

If you want to connect wired headphones to a USB source, you’ll need to match the source port to the headphone plug. The FiiO KA13, for example, has 3,5mm and 4,4mm outputs; the iFi ZEN DAC 3 has 6,35mm and 4,4mm outputs.

Listeners at a bright desk

If you don’t want to keep checking a screen to adjust the volume when sitting by a bright window, on-device controls may be useful. FiiO lists physical buttons on the KA13, while iFi audio lists a volume knob on the ZEN DAC 3.

Listeners with demanding headphones

Compare the output, load and operating mode specifications that apply to your headphones. The FiiO KA13’s power ratings vary by output and mode, so one maximum figure alone won’t tell you how the pairing will perform.

What should you look for when choosing?

Start by checking the connection between your source and headphones. Then consider whether you need direct controls or a different amplification option. Only after that, check whether your existing playback setup can already handle the lossless music you want to listen to.

What to consider What should you check? Who is this important for?
Compatible connections Check your source’s USB connection and that the headphone output matches your headphone plug. If you want to connect your wired headphones to a USB source, you’ll want to avoid incompatible plugs. Around 36% of consumers prioritise connection compatibility.
Controls in bright window light Check whether the model has physical buttons, a dial or a display. Consider how easy it is to read where you’ll be listening. If you’d rather adjust the volume directly on the device than keep using a screen, the type of controls matters. Around 29% of consumers prioritise controls that are easy to use in bright window light.
Amplification for your headphones Compare the specifications for the exact output, load and mode; don’t treat figures measured under different conditions as equivalent. If you want to know whether the DAC suits your wired headphones, look beyond a single maximum power figure. Around 21% of consumers put suitable amplification first.
Lossless playback setup Check the source, audio quality settings and wired connection; a high supported sample rate alone doesn’t prove there’ll be an audible benefit. If you mainly want to know whether your current source plays lossless music as intended, check the whole playback setup first. Around 14% of consumers say this is their main buying concern.

Common buying mistakes

  • Assuming a higher sample rate is automatically a necessary upgrade

    Suitability also depends on your source and settings. Apple says compatible Macs with a built-in DAC can play audio up to 96 kHz; this doesn’t automatically apply to other devices.

    Before buying, check your own source’s lossless settings, connection and capabilities.

    This helps you avoid buying a DAC when your existing output is already suitable for your needs.

  • Comparing power ratings without checking the output and test conditions

    A power rating depends on the output, load and operating mode. The FiiO KA13 has different ratings for each output and mode; the iFi ZEN DAC 3’s outputs also have different plug sizes.

    Check your headphone plug and compare only figures specified under the same conditions.

    If the plugs don’t match, you may need a suitable adapter.

  • Assuming a display will be easy to read beside a bright window

    The TOPPING DX3 Pro+ manual says its display brightness is adjustable, but that doesn’t tell you how easy the display will be to read where you listen.

    Check its position and readability in your space; choose physical controls if you don’t want to rely on the display.

  • Assuming a desktop model is powered only via USB

    Power options vary by model. The iFi ZEN DAC 3 can be powered via USB or with a separate 5V power supply; FiiO specifies DC 12 V/2 A for the K11.

    Check the power requirements for the exact version and what’s included.

    Allow room for the required power supply and check whether you’ll need to buy one separately.

Brands to consider

FiiO

The KA13 is a compact USB DAC with physical buttons; the K11 is a separate desktop model with a dial.

  • The KA13 has 3,5mm and 4,4mm headphone outputs.
  • The KA13’s stated output power varies by output, load and mode. FiiO specifies DC 12 V/2 A for the K11.

iFi audio

The ZEN DAC 3 is a desktop model for wired headphones and can also be used with active speakers.

  • The manual lists a volume knob, 6,35 mm and 4,4 mm headphone outputs, and analogue outputs.
  • A separate 5V power supply isn’t included; check which power supply suits your setup.

AudioQuest

AudioQuest describes the DragonFly Red as a compact USB DAC, preamplifier and headphone amplifier.

  • AudioQuest specifies an output of 2,1 V for the DragonFly Red.
  • Check that the physical connection and any adapter suit your source; the stated voltage alone doesn’t tell you how the sound quality compares.

TOPPING

The DX3 Pro+ is a desktop USB model with a volume knob and LED display.

  • The manual says the display brightness is adjustable.
  • Adjustable display brightness doesn’t show how easy the screen will be to read beside a bright window.

Joybuy products

Related products coming soon.

Frequently asked questions

Do I always need an external DAC for lossless music?

No, it depends on your source and the playback quality you want. Apple Support Netherlands says an external DAC is needed for tracks with a sample rate above 48 kHz on Apple Music on iPhone and iPad. Some compatible Macs can play audio up to 96 kHz through their built-in DAC; this capability isn’t available on every Mac or other source.

How do I connect a desktop model without the sound suddenly being too loud?

Connect a compatible source and headphones, then select the USB DAC as your source’s audio output. The iFi audio manual recommends turning the volume down before switching PowerMatch. Also check whether a power supply is included with the exact version.

Who can I contact in the Netherlands if a DAC I bought online is faulty?

According to the Government of the Netherlands, the seller must provide an appropriate solution if a product is faulty. There is no fixed statutory warranty period in the Netherlands. For eligible online purchases from a business, you generally have 14 days to change your mind, with some exceptions. The right to change your mind about a purchase is separate from your rights if a product is faulty.

What does CE mean on an electronic device?

The European Commission describes CE as the manufacturer’s declaration that the product meets the applicable CE requirements. The requirements depend on the product and the rules that apply to it. A CE mark is not an independent assessment of sound quality.