Who is this relevant to?

Server administrator looking for a safe shutdown

You want to avoid a prolonged power cut shutting down your server while it’s writing data. Synology and Network UPS Tools explain how a supported UPS connection and a configured shutdown procedure can help.

User looking to ride out brief power cuts

You want to keep your server running during a brief power cut, and perhaps your router or switch too. Compare their combined power draw with the runtime at that load. UPS manufacturers publish different power and runtime specifications for their models.

User short on desk space

You’re looking for a practical spot for the UPS and its cables, with the server plugged into a battery-backed socket. Also check that the plugs will fit and whether the battery can be replaced, if that matters to you for maintenance.

What should you look for when choosing?

Compact standby UPS with USB

Suitable for: a modest, measured load and a short period of backup power, provided the server can process the UPS status.

Check: which sockets provide battery backup and whether the runtime is sufficient for your load.

Line-interactive with AVR

Suitable for: a setup where automatic voltage regulation is important.

Check: AVR alone tells you nothing about runtime, server communication or the space required.

Line-interactive with pure sine wave output

Suitable for: a server power supply that requires a pure sine wave output.

Check: a manufacturer’s compatibility claims don’t confirm that the UPS will work with your specific server. Check the power supply requirements and battery-backed outputs.

Buying priority What should you check? Who might value this more?
Controlled shutdown Check that the UPS and server communicate with each other, that the operating system supports the connection, and that the shutdown procedure is set up and tested to run before the battery runs out. If I want my server to shut down safely in good time during a prolonged power cut, I check the entire connection and procedure; around 33% of consumers put controlled shutdown at the top of their list.
Runtime at actual power draw Measure the combined power draw in watts and compare it with runtime figures for a similar load. If I want the server and essential network equipment to keep running during a brief power cut, I check the runtime at their combined load; around 27% of consumers prioritise backup time.
Electrical connections Compare the plug type, the number of battery-backed outputs and the server power supply’s requirements for the output waveform. If I want to make sure my plugs fit and the server is connected to a battery-backed output, I also check the power supply requirements; around 20% of consumers prioritise electrical compatibility.
Space and maintenance Check the dimensions and form factor, including the space needed for cables, and find out whether the battery is replaceable. With limited desk space, I want to know where the UPS can go with its cables and what battery maintenance involves; around 20% of consumers prioritise desk space and ease of maintenance.

Common buying mistakes

  • Assuming every socket provides battery backup

    Some UPS models have sockets that only provide surge protection, as well as battery-backed outputs. Equipment plugged into those sockets won’t receive battery power during a power cut.

    Before buying, work out which devices will plug into each output and check which outputs provide battery backup.

  • Assuming a high VA rating means sufficient runtime

    The VA or watt rating doesn’t tell you how long the UPS can power your server and network equipment at their combined load. Runtime figures at half load apply to that stated load, not automatically to your setup.

    Measure the combined power draw in watts, compare runtime figures for a suitable load, then test the shutdown procedure.

  • Confusing a USB charging port with a UPS data connection

    For automatic shutdown, the server must be able to receive and process UPS status information. A USB charging socket doesn’t provide this communication.

    Check separately which communication protocol and connection the UPS offers, and whether the server’s operating system supports that combination.

Brands to consider

Eaton

The 3S Gen2 range includes compact standby models. The Dutch Schuko version reviewed is the 3S550D.

  • Eaton specifies USB-HID and 550 VA/330 W for the 3S550D; its battery is replaceable.
  • Three of the six Schuko sockets provide battery backup; the other three only provide surge protection.
  • Eaton lists the older 3S range as discontinued. This does not apply to the 3S Gen2.

APC by Schneider Electric

The Dutch Back-UPS models reviewed include line-interactive versions with AVR and Schuko sockets. Always compare the full model code.

  • Schneider Electric lists four Schuko sockets with battery backup for the BX950MI-GR.
  • The planned end of sales for the BX750MI-GR on 31 December 2026 and the end of standard service on 31 December 2028 apply to that model, not the whole range.

CyberPower

The CP900EPFCLCD reviewed is a European line-interactive option with pure sine wave output.

  • CyberPower specifies 900 VA/540 W, six Schuko sockets and AVR.
  • The stated runtime of seven minutes applies at half load. The manufacturer’s claim that it’s suitable for power supplies with active PFC doesn’t by itself confirm compatibility with your server.

PowerWalker

The VI 1000 CSW is a line-interactive tower model with pure sine wave output and USB-HID.

  • BlueWalker specifies 1000 VA/600 W and a replaceable battery.
  • Two of the four Schuko sockets provide battery backup; the other two only provide surge protection. The stated runtime of seven minutes applies at half load.

Joybuy products

Related products coming soon.

Frequently asked questions

How do I set up automatic shutdown?

Connect the UPS using a connection and protocol supported by your server, set a shutdown time that falls before the battery runs out, and test the procedure. Network UPS Tools explains how to set up communication and a safe shutdown. On a Synology NAS, the UPS function is designed to save data and unmount volumes. Check support for your specific setup.

Should I connect the router to the UPS too?

Connect the router to a battery-backed output too if the server needs to remain accessible over the network during a power cut. Include the power draw of both devices and use a battery-backed output for the router, not one that only provides surge protection.

What should I check about battery maintenance and the warranty?

Check whether the battery is replaceable for the specific model and which replacement battery is suitable. For a purchase by a consumer in the Netherlands, statutory consumer rights are separate from the manufacturer’s warranty; the retailer is your point of contact if a product is faulty. According to the Dutch government, there is no fixed statutory warranty period in the Netherlands.

What are the rules on CE marking and disposal in the Netherlands?

For a UPS covered by harmonised EU rules, the manufacturer must comply with the applicable rules and apply the required CE marking. According to Your Europe, the marking is only required when such rules say it is. A CE marking doesn’t prove that the model is suitable for your server. Dispose of an old UPS through an appropriate collection scheme for electrical appliances, and don’t put a spent battery in household waste, as advised by the Dutch government.