NAS owner looking to reduce the risk of data loss
You want your NAS to detect a power cut and shut down in a controlled way. Synology and QNAP recommend checking support for your specific NAS and UPS models.
First, choose a UPS that communicates with your NAS model. Then, work out how long you need it to run based on the connected load, so you can shut down safely or keep your equipment running temporarily. Also check the permitted temperature and humidity where you plan to install the UPS. The rated capacity in VA or W alone won’t tell you how long your NAS will run on battery power.
You want your NAS to detect a power cut and shut down in a controlled way. Synology and QNAP recommend checking support for your specific NAS and UPS models.
You may also want to keep your network equipment powered temporarily. So consider the combined load, the connections you need and the runtime you’re aiming for.
The temperature and humidity where you install the UPS can be important. Follow the environmental limits for the exact model.
First, check that the UPS can communicate with your NAS. Then calculate the total load and runtime you need, and make sure the space and connections are suitable for your chosen model.
| What to consider | What to look for when buying | Who should consider this? |
|---|---|---|
| NAS communication and safe shutdown | Check that your NAS model supports the UPS, and test the response you’ve set for a power cut. | Do you want your NAS to receive a signal and shut down in a controlled way during an outage? Around 33% of consumers prioritise safe shutdown. |
| Runtime under load | Add up the devices that need battery power and compare runtime figures for that same load. Check both the W and VA limits. | If you want to keep the NAS running temporarily, or power network equipment too, weigh the runtime you need against the combined load. Around 25% of consumers prioritise temporary availability. |
| Conditions in your garden office | Compare the temperature and humidity where you plan to install the UPS with the limits for the exact model. Keep the ventilation openings clear. | If the UPS will be in an unheated room, check that the location is within the model’s specifications. Around 25% of consumers prioritise finding a suitable installation location. |
| Connections and battery maintenance | Check which outlets provide battery power, which cables you’ll need and whether the battery in the exact model can be replaced. | Do you want to connect your NAS correctly and know what maintenance options are available later? Around 17% of consumers prioritise connections and battery maintenance. |
Runtime depends on the connected load. Devices such as network equipment count towards it if they also need to stay on battery power.
First, calculate the load and compare it with runtime figures for the same load. Then set the shutdown time to suit your NAS.
That kind of outlet won’t provide battery power during a mains failure. According to Eaton, one of the four C13 outlets on the Eaton EL800USBIEC provides surge protection only.
Check the markings on each outlet for the exact model and plug your NAS into an outlet with battery backup.
Permitted temperature and humidity vary by model. Eaton specifies a range of 0–35 °C and 0–85% relative humidity, non-condensing, for the Eaton EL800USBIEC.
Check the conditions at your intended installation location and follow the manual for your chosen UPS.
If the location falls outside the model’s specifications, you may need to install the UPS somewhere else.
The Ellipse ECO USB models are worth considering if a compact UPS with USB communication suits your NAS setup.
The CP900EPFCLCD is a line-interactive model with AVR. Its output waveform may be relevant to the equipment you want to connect.
The Edge range is worth considering if you want to include multiple IT devices or remote management in your decision.
No. Check support for your specific NAS and UPS models, and test the response you’ve set for battery operation. Synology describes USB UPS support and recommends simulating a power cut; QNAP also recommends testing compatibility and shutdown.
Only if you want to access the NAS over your local network during a power cut and need network equipment to do so. Those devices increase the combined load and can affect runtime.
That depends on the exact model and the conditions at the location. Eaton specifies 0–35 °C and 0–85% relative humidity, non-condensing, for the EL800USBIEC; a Vertiv manual for a different model requires a controlled, dry indoor environment. Don’t apply the limits for one model to another.
Check which battery type the exact model uses and whether the battery can be replaced. Eaton says the EL800USBIEC has a user-replaceable battery; this doesn’t tell you the current price or availability of a replacement battery.
According to the Netherlands Food and Consumer Product Safety Authority, a UPS offered on the Dutch market as an electrical product must carry a CE marking. A CE marking alone does not prove that the specific unit has been independently tested.