Who is this for?

Mixer with limited access to sockets

You want to listen to a soundtrack without having to charge headphones or a separate amplifier. Do check that your playback device has power and a suitable headphone output. Focusrite explains how to connect headphones to an interface’s audio output; beyerdynamic also distinguishes between DT 770 PRO versions based partly on the source being used.

Editor working during rehearsals

You work near other people, background noise or a microphone, and want to minimise sound bleed. Audio-Technica explains why keeping sound bleed low can matter when recording with microphones.

Mixer in a quiet space

You’re mainly assessing the positioning and balance of soundtrack tracks, so isolation may be less of a priority. Sennheiser describes the open-back HD 490 PRO as a model for production and mixing; an open-back design provides less isolation.

What should you look for when buying?

Wired, closed-back

Best for: mixing or checking takes during rehearsals, around other people or close to a recording microphone, when you want to reduce sound bleed and background noise.

Keep in mind: the fit affects the seal. A closed-back design doesn’t guarantee a neutral mix or the same sense of space as an open-back model.

Wired, open-back

Best for: a quiet space where you’re mainly assessing balance and positioning, with no microphone or colleagues nearby.

Keep in mind: an open-back design provides less isolation and can let sound escape. Background noise can make quieter passages harder to assess. Audio-Technica explains these differences between open-back and closed-back models.

What to consider What should you check? Who is this important for?
Few spare sockets Check that your source has power, and check the headphone output, connector and available volume at a safe listening level. Wired headphones don’t remove the need to power your source. I want to mix without needing an extra headphone charger. Around 33% of consumers put working without an additional charging point first.
Isolation during rehearsals or recording Check that the ear pads fit snugly and whether a microphone picks up sound from the headphones. Audio-Technica explains why minimising sound bleed can matter when recording. When I’m working near other people or a microphone, I want to reduce distracting background noise and sound bleed. Isolation is the top priority for around 27% of consumers.
Spatial positioning Compare an open-back model in a quiet space and listen to familiar passages. Check the mix through the intended playback system too. An open-back model provides less isolation. In a quiet workspace, I mainly want to assess the balance and positioning of tracks. Around 27% of consumers prioritise assessing a mix’s spatial presentation.
Long-term comfort and maintenance Consider the fit and cable length, and check which replacement parts are available for the exact version. For long editing sessions, I want comfortable headphones with parts that can be maintained. This is the top priority for around 13% of consumers.

Common buying mistakes

  • Assuming wired means a setup that needs no power at all

    Wired headphones don’t need their own charger, but your playback device or audio interface still needs power and must be able to output audio. Focusrite explains how to connect headphones to an interface output.

    Before buying, check the entire signal chain: playback device, any interface, headphone output, connector and power supply.

  • Treating different DT 770 PRO versions as the same model

    beyerdynamic offers the DT 770 PRO in 32, 80 and 250 ohm versions, and recommends them for different sources. The DT 770 PRO X is a separate 48-ohm model with a detachable mini-XLR cable.

    Compare the full model name and impedance with your source, and check the cable supplied with the exact version.

  • Choosing open-back headphones without considering the rehearsal environment

    An open-back design provides less isolation and can let sound escape. This may be inconvenient if you’re working near other people or a microphone.

    First decide whether you’ll mainly be mixing in a quiet space or also working near other people or a microphone. Then compare open-back and closed-back models.

Brands to compare

beyerdynamic

The closed-back DT 770 PRO is available in several impedance options, so you can choose the version to suit your source.

  • beyerdynamic lists replaceable ear pads for the DT 770 PRO.
  • The manufacturer recommends the 32, 80 and 250 ohm versions for different uses. The DT 770 PRO X is a separate 48-ohm model, so check the full model name and version.

Audio-Technica

The wired, closed-back ATH-M50x is worth comparing if isolation and detachable cables are important to you.

  • Audio-Technica lists passive isolation and three detachable cables for the ATH-M50x.
  • These are the manufacturer’s specifications and descriptions, not independent measurements of isolation or a guarantee of neutral mixing decisions.

Sony

The MDR-7506 is worth comparing for studio and recording work, particularly if a 3 m cable would be useful.

  • Sony Netherlands lists a 3 m cable and a design weight of 230 g for the MDR-7506.
  • Check that the cable length suits your workspace. Sony’s description of the headphones as a reference model is not independent confirmation of neutral sound.

Sennheiser

The open-back HD 490 PRO is worth comparing for a quiet space where isolation isn’t a priority.

  • Sennheiser lists two interchangeable sets of ear pads for production and mixing, as well as a detachable cable.
  • Its open-back design makes this model less suitable if you want to reduce background noise or sound bleed.

AKG

The closed-back K371 is another option to compare for mobile studio work where isolation matters.

  • AKG specifies an impedance of 32 ohms and a weight of 255 g for the K371.
  • AKG’s claims about neutrality, isolation and comfort aren’t independent measurements; fit is a personal matter.

Joybuy products

Related products will be available soon.

Frequently asked questions

Do wired studio headphones need no power at all?

The headphones themselves don’t need a separate charger, but your laptop, recorder or audio interface still needs power and must be able to drive them. Check the output and power supply before working on location.

How do I connect studio headphones to my audio interface?

Use the dedicated headphone output and check that the connector matches. Some 3.5 mm plugs need a suitable stereo adapter to work with a 6.35 mm output. Also check that the cable reaches your listening position.

When should I replace the cable or ear pads?

If the sound cuts out or the seal changes, first check the connection, cable and fit. Audio-Technica lists detachable cables for the ATH-M50x; beyerdynamic lists replaceable ear pads for the DT 770 PRO, and Sennheiser does so for the HD 490 PRO. Check which parts are compatible with your exact version.

Am I always entitled to exactly two years’ legal guarantee when buying as a consumer in the Netherlands?

No. ACM ConsuWijzer explains that your legal guarantee depends on what you could reasonably expect from the product under normal use, and that the seller is responsible for it. A two-year manufacturer’s warranty therefore doesn’t automatically mean that your legal entitlement lasts exactly two years.

Can I return headphones bought online if they don’t fit comfortably?

For a standard online consumer purchase, you usually have a legal cooling-off period of up to and including 14 days after delivery, subject to legal exceptions. ACM ConsuWijzer explains this cooling-off period; check the seller’s returns information before buying too.