Who are these monitors for?

Percussion editor with limited desk space

Wants to set up a stereo listening position without occupying the shared desk for long periods. Compact dimensions and placement controls can help; ADAM Audio and Kali Audio describe these features for the models mentioned here.

Editor who checks transients closely

Assesses timing, individual hits and the balance between them. A consistent listening position is important: Genelec recommends an equilateral triangle for stereo monitoring, with the listener at the third corner.

Editor who checks kick drums and toms

Wants to assess the low end and compare frequency response figures alongside their measurement tolerances. Kali Audio, Yamaha, Genelec and ADAM Audio use different dB definitions in their specifications, so the lowest stated frequency is not directly comparable on its own.

What should you look for when choosing?

First, measure the space available for two monitors and decide where you’ll be listening each time. Then check the connections and frequency specifications: a low-frequency figure is only meaningful for comparison when the measurement tolerance is the same.

Buying concern What to look for Who is it more important to?
Positioning on a shared desk Measure the width and depth available for a stereo pair; check the feet, placement controls and space for cables. If I share the desk, I want to be able to set up two monitors and then clear the space without having to work out my listening position all over again. Around 31% of consumers say positioning is their main buying concern.
Transients, timing and stereo positioning Check whether two monitors can be positioned symmetrically and at the same height; take desk reflections into account. If I’m assessing individual hits and left-right balance, I want to listen from a fixed position in consistent conditions. Around 25% of consumers prioritise checking transients and stereo imaging.
Working without disturbing others Check that the volume control is easy to reach and that the set has a headphone output if you need one. If I share a workspace with others, I want to adjust the volume easily and switch to headphones when using speakers isn’t practical. Around 25% of consumers say keeping noise to others to a minimum is their main buying concern.
Low end from kick drums and toms Compare frequency response figures using the same tolerance, such as −3, −6 or −10 dB; also consider the space and positioning options. If I’m assessing kick drums and toms, I want to know under what measurement conditions a low frequency is specified and whether the monitor will suit my listening position. Around 19% of consumers prioritise low-end control.

Common buying mistakes

  • Comparing the lowest frequency directly

    Manufacturers use different tolerances, including −3, −6 and −10 dB. Without the same measurement basis, a lower figure doesn’t prove that you’ll hear kick-drum low end more accurately in your listening position.

    Note the tolerance alongside each frequency response figure, and consider how the monitors will fit in your space.

  • Mistaking a single monitor for a stereo pair

    Genelec sells the 8010A as a single monitor; Yamaha specifies the HS4 as a pair. This affects how many units you’ll need for stereo.

    Check what’s included in the box and compare the complete stereo setup, not just one speaker.

  • Looking only at cabinet size

    A compact model won’t automatically work well on a shared desk. Positioning, equal height and reflections from the desk all affect your listening setup; Genelec also warns that a desk can resonate.

    Before buying, check that both monitors can sit securely and be angled towards your listening position. If there isn’t a suitable spot on the desk, separate stands may take up extra space.

Relevant brands to compare

ADAM Audio

The D3V is a compact desk setup; the T5V is a larger, single nearfield monitor. These are differences between models, not general features of the brand.

  • ADAM Audio lists USB-C, TRS connections, included feet and placement switches for the D3V.
  • The T5V is a single monitor with a rear-facing bass reflex port. The manufacturer specifies a range of 45 Hz–25 kHz at −6 dB.

Kali Audio

Kali Audio describes the LP-UNF as an active ultra-nearfield stereo system designed for desk placement.

  • Kali Audio lists settings for desk and wall placement, as well as USB-C, TRS and RCA connections.
  • The specified 39 Hz figure is at −10 dB; the range within ±3 dB starts at 54 Hz. These figures therefore refer to different measurement conditions.

Yamaha

The HS4 is a compact analogue monitor system specified as a pair.

  • Yamaha lists a headphone output and low- and high-frequency controls.
  • According to the manufacturer, the HS4 has no USB audio input. The European specification sheet gives 60 Hz at −10 dB and 83 Hz at −3 dB.

Genelec

The 8010A is a small active monitor sold individually.

  • Genelec specifies a width of 121 mm and one analogue XLR input per monitor.
  • You’ll need two units for stereo. The specified lower limit is 67 Hz at −6 dB.

IK Multimedia

IK Multimedia describes the iLoud Micro Monitor as a compact active stereo system with analogue and Bluetooth inputs.

  • The manufacturer lists a desk setting and a specified lower limit of 45 Hz at −10 dB.
  • IK Multimedia specifies Bluetooth latency of 155 ms under its own described test conditions. For time-critical editing, use a suitable wired connection.

Joybuy products

Related products will be available soon.

Frequently asked questions

How do you set up two monitors when sharing a desk?

Where possible, mark out a repeatable, symmetrical position at equal height and angle both monitors towards your listening position. Genelec recommends an equilateral triangle for stereo monitoring; reflections from the desk and room are still worth considering.

Is Bluetooth suitable for editing percussion?

For time-critical assessment of hits, it’s best to use a suitable wired input. IK Multimedia specifies Bluetooth latency of 155 ms for the original iLoud Micro Monitor under the stated test conditions; this figure does not automatically apply to other models or devices.

How can you minimise disturbance and avoid listening too loudly?

Agree listening times and volume levels with other users. The World Health Organization links the risk of hearing damage to both sound level and duration of exposure; the Dutch government advises trying to resolve music-related disturbance by agreeing things with others first.

What happens if you return a product or it develops a fault after purchase?

For an online consumer purchase, ACM ConsuWijzer states that you have a statutory 14-day cooling-off period after delivery, with some exceptions. This is separate from a fault: if a product doesn’t perform as you could reasonably expect under normal use, the seller is responsible for providing an appropriate solution.

Which product requirement should you check when buying in the Netherlands?

Electrical and electronic equipment is subject to the applicable EU rules on CE marking. Check the marking and documentation for the specific version on offer; general model specifications don’t automatically confirm that a particular offer complies.