Who is this choice relevant to?

Editor with one free mains socket

Wants to listen back to rehearsals in stereo without having to reserve a separate power connection for each speaker.

Editor of recordings with a busy band mix

Wants to assess vocals, guitars, drums and relative levels, and has room for a fixed listening setup.

Music maker with an existing amplifier

Wants to check whether passive reference monitors are compatible with the amplifier, while bearing in mind their more limited bass response.

What should you look for in studio monitors?

When editing rehearsal recordings, the power setup matters, as do the connection to your recording equipment, your listening position and how closely you want to assess the kick drum and bass.

What to consider What to look for when buying Who is this most relevant to?
Power connections Check whether one or both speakers need mains power, and whether the connecting cable is included and long enough. If you have limited mains sockets, you’ll want to know in advance how power is distributed across a stereo pair. Around 31% of consumers prioritise the number of power connections needed.
Separating vocals and instruments Check whether the tone controls can be set neutrally for critical listening. Mackie describes the CR3.5’s tone knob as flat when turned fully to the left. With a full band recording, you’ll want to assess vocals and instruments separately, rather than just hear a coloured sound. Around 25% of consumers prioritise this clarity.
Room and listening position Measure the available space and check which placement or room controls the model has. Yamaha lists ROOM CONTROL and HIGH TRIM for the HS5; your chosen settings should suit its actual placement. If your desk or room limits your setup, you’ll want to position the left and right monitors properly around your listening position. Around 19% of consumers prioritise their room and listening position.
Connection to your recording setup Compare the outputs on your computer, recorder or interface with the monitors’ inputs, and check which cables are included. You’ll want to connect your existing recording equipment without using the wrong cable. Around 13% of consumers prioritise this connection.
Assessing kick drum and bass Read a frequency limit alongside its stated dB tolerance. ADAM Audio lists 45 Hz at −6 dB for the T5V; don’t compare this directly with figures measured using a different tolerance. If you want to assess the kick drum and bass, you’ll want to know the conditions under which the stated frequency limit applies. Around 12% of consumers prioritise bass assessment.

Things to watch out for when buying studio monitors

  • Assuming both speakers need their own plug

    A stereo pair with one powered speaker and one passive partner has a different power setup from two separately powered monitors.

    Check which speaker needs mains power in the exact model you’re considering, and whether the connecting cable is long enough for your setup.

  • Assuming a passive monitor doesn’t need a power supply

    A passive monitor needs a suitable amplifier. The amplifier itself takes up space and needs power and cabling.

    Check that your amplifier is compatible and compare the complete setup before choosing passive speakers.

    If you don’t already have a suitable amplifier, you’ll need to include one in your setup.

  • Comparing monitors’ frequency limits directly

    A frequency figure only makes sense in the context of its stated measurement tolerance. Your room also affects how much bass you hear.

    Compare frequency limits only when you also have their dB tolerances, and assess the monitors where you plan to use them.

Brands to consider for this setup

PreSonus

The Eris 3.5 2nd Gen is a compact stereo pair with several analogue inputs.

  • PreSonus lists tone controls and a headphone output; a speaker cable is included with the pair.
  • The stated frequency range starts at 80 Hz. This doesn’t prove that you can fully assess the deepest bass in a rehearsal recording.

Mackie

The CR3.5 (Gen 3) is a compact stereo pair with adjustable tone and different placement modes.

  • Mackie describes a tone control and a switch between desktop and bookshelf placement.
  • Your chosen tone setting affects what you hear; Mackie says that turning the control further adds bass and treble.

Yamaha

The HS5 is a separately powered nearfield monitor with XLR and TRS inputs.

  • Yamaha lists ROOM CONTROL and HIGH TRIM for the HS5.
  • The stated power consumption of 45 W applies to each monitor, not to a complete pair in use.

ADAM Audio

ADAM Audio positions the T5V as an active nearfield monitor for smaller control rooms.

  • The manufacturer lists a 5-inch woofer and a frequency range of 45 Hz–25 kHz at −6 dB.
  • The stated frequency limit is a manufacturer’s specification, not a measurement taken in your room. The bass reflex port is at the rear.

Avantone Pro

The passive Mixcube is an additional reference monitor for a setup with an amplifier.

  • Avantone Pro lists a nominal impedance of 8 ohms and a recommended amplifier power of 10–200 W.
  • With a stated range of 200 Hz–10 kHz, the Mixcube isn’t a complete reference for bass in band recordings.

Studio monitors on Joybuy

Related products coming soon.

Frequently asked questions about studio monitors for rehearsal recordings

Does an active stereo pair mean both speakers need their own mains socket?

No, not necessarily. Some sets combine one powered speaker with a passive partner. Check which speaker needs power in the exact model you’re considering, and whether the connecting cable suits your setup.

How should you position monitors to assess a rehearsal recording?

Start by placing both monitors at a similar distance from your listening position. Genelec points out that the listening room and reflections affect what you hear; adjust the room controls to suit the actual placement. With the Mackie CR3.5, also take into account whether you’ve chosen desktop or bookshelf mode.

How can you use a powered monitor setup safely?

Follow the manual for the exact model. For the CR3.5, Mackie recommends allowing plenty of ventilation and warns against overloading mains sockets or extension leads. This is especially relevant when you have limited connections available.

Does a two-year manufacturer’s warranty provide the full warranty in the Netherlands?

No. ACM ConsuWijzer distinguishes between a manufacturer’s or seller’s warranty and the legal guarantee. A product must meet the standard you could reasonably expect during normal use; if it develops a fault too soon, the seller is responsible for providing an appropriate solution. The legal guarantee period isn’t exactly two years for every product.

Which rules apply to electric monitors or monitors with Bluetooth?

Business.gov.nl explains that electrical and electronic equipment must comply with the applicable European rules, and also lists rules for radio equipment that uses Bluetooth. A CE mark is the manufacturer’s declaration of conformity, not an independent quality mark. Check the conformity information for the specific product.