Who is this guide for?

Guitarists who need to record quietly

If you’re recording with a microphone or there are other people nearby, headphone monitoring is important while you record. You can use speakers later to assess the recording. Focusrite warns that active speakers can cause feedback when monitoring a microphone.

Guitarists with a small desk

You’ll want to position two speakers neatly and symmetrically around your listening position. So compare their dimensions and check whether the box contains one monitor or a pair.

Guitarists who mix recordings

You’ll want to assess stereo positioning, tonal balance and bass. Bear the placement and room in mind: a frequency limit in the specifications isn’t a measurement taken at your listening position.

What should you look for?

Start by thinking about how you’ll monitor while recording. Then check whether a pair of speakers will fit on your desk and whether their connections are compatible with your audio interface.

What to consider What should you check? Who is this important for?
Recording quietly Check your interface’s headphone monitoring route and direct monitoring function. A headphone output on a speaker isn’t automatically the same as a recording monitoring route. If I’m recording guitar with a microphone or don’t want to disturb others, I want to monitor through suitable headphones while recording. Around 36% of consumers prioritise being able to record quietly.
Desk space and placement Measure the space available for two speakers and allow for their positioning and cables. A compact cabinet doesn’t guarantee neutral sound in every room. With limited desk space, I want to be able to position two monitors symmetrically around my listening position. Around 29% of consumers are mainly concerned with having space for a suitable stereo pair.
Mixing and bass Compare frequency limits only when they use the same dB tolerance. Assess the sound from a fixed listening position; settings can’t replace suitable placement. When I’m mixing guitar recordings, I want to assess tonal balance and bass from my usual listening position. Around 21% of consumers prioritise mix monitoring.
Connections and what’s in the box Compare your interface’s outputs with the inputs on both monitors. Check whether the box contains one speaker or a pair, and allow for any extra cables you may need. I want to connect my interface without unexpectedly ending up with just one speaker. Around 14% of consumers prioritise connections and a complete stereo setup.

Common mistakes

  • Mistaking a single monitor for a stereo pair

    The Genelec 8010A is sold individually, while Yamaha specifies the HS3 as a pair. If the box contains one monitor, you’ll need a second one for stereo.

    This may also mean buying a second speaker and the right cables.

    Before you buy, check what’s included in the box and count the two stereo channels and the connections you’ll need.

  • Choosing based only on the lowest frequency figure

    Specifications may use different measurement tolerances: Yamaha lists the HS3 at 85 Hz at −3 dB, while the T5V and 8010A state their frequency limits at −6 dB. Your room and listening position also affect what you hear.

    Only compare frequency limits measured on the same basis, and assess placement and listening position separately.

  • Leaving speakers on while recording with a microphone

    A microphone can pick up sound from active monitors. Direct monitoring and software monitoring of the same input signal can also play at the same time.

    Feedback or unwanted sound from the speakers could mean you have to record the take again.

    Use a suitable headphone monitoring route while recording this way, and check your interface’s monitoring settings.

Brands to consider

PreSonus

The Eris 3.5 2nd Gen is a compact stereo pair for a desk, with the added convenience of being able to switch to headphones easily.

  • According to PreSonus, the pair has TRS, RCA and stereo mini-jack inputs, as well as a headphone output on the front.
  • The stated lower limit of 80 Hz doesn’t specify a dB tolerance, so it doesn’t tell you how the bass will sound in your room. Don’t confuse the wired version with the separate BT version.

Yamaha

The HS3 is a compact pair with several analogue inputs and adjustable room and high-frequency controls.

  • Yamaha’s European specifications state that the HS3 comes as a pair, with a frequency response from 85 Hz at −3 dB.
  • That frequency limit doesn’t predict how the monitors will sound in your room. Also check that the different connections on the left and right speakers will work with your desk setup.

ADAM Audio

The T5V is a single 5-inch nearfield monitor for anyone with space to plan for two monitors and their placement.

  • ADAM Audio specifies a rear-facing bass reflex port and 45 Hz at −6 dB.
  • Its description as suitable for small control rooms is a manufacturer’s claim, not an independent assessment of your room. Check the available space, number of monitors and cabling you’ll need.

Genelec

The 8010A is a very compact, single active monitor with an analogue XLR input and room compensation switches.

  • Genelec specifies a width of 121 mm, a limit of 67 Hz at −6 dB and one monitor per box.
  • You’ll need two for stereo. Describing its sound as neutral is a manufacturer’s claim, not a measurement taken at your listening position.

KRK

The ROKIT 5 Generation Five is a single 5-inch monitor for anyone who wants to compare monitoring settings and has room for a pair.

  • KRK lists three sound modes and 25 combinations of boundary and EQ settings.
  • These features don’t prove that they’ll eliminate room problems. The Dutch product listing for the RP5 G5 also refers to a single monitor.

Joybuy products

Related products coming soon.

Frequently asked questions

Should I monitor through speakers while recording guitar?

Not if you’re using a microphone and sound from the speakers could get into the recording. Focusrite warns that active speakers can cause feedback when monitoring a microphone, so use a suitable headphone monitoring route instead. If you can hear a delay, direct monitoring on a suitable interface may help.

How should I position two monitors to assess recordings?

Aim both monitors at the same fixed listening position and try to place them symmetrically on the left and right. Genelec recommends an equilateral triangle for stereo monitoring where possible. Also bear in mind that your desk and room can affect the sound.

What should I check about the cables and what’s in the box?

Check that the connections are compatible with your audio interface and how many speakers are included. Yamaha specifies the HS3 as a pair; a Genelec 8010A box contains one monitor with one XLR input. For the PreSonus Eris 3.5 2nd Gen, also check that the connection and source cables listed by the manufacturer will work with your interface.

How can I avoid disturbing other people with my monitors?

When recording with a microphone, use a suitable headphone monitoring route if speaker sound could disturb others or be picked up by the microphone. The Dutch government advises neighbours experiencing noise nuisance to discuss and agree on a solution first; also check any local rules and the rules for your home.

What warranty and cooling-off period apply to an online purchase in the Netherlands?

For distance purchases from a business, a 14-day cooling-off period applies in many cases, although there are exceptions. You’re also entitled to a legal guarantee when you buy a product; a manufacturer’s or seller’s guarantee is an additional benefit. Before placing your order, check the terms of the specific seller and any return costs.