Who is this buying guide for?

Dialogue editor

You check whether speech still sounds clear after noise reduction and whether the processing has introduced audible side effects. Adobe and iZotope recommend listening back to the result; iZotope also stresses keeping the original so you can compare the two.

Editor with a small desk

You want to position the speakers around a screen, so you’re considering cabinet dimensions, symmetry and your listening position. Genelec offers placement advice for studio monitors.

Editor who also checks for hum

As well as speech, you listen for low-frequency interference and want to know what a compact monitor can help you assess in your setup. Compare frequency limits only when they have the same measurement tolerance.

What should you look for?

Start with your room and listening position, then check the connections and what’s included in the set. Finally, consider whether you need manual or measurement-based calibration.

What to consider What should you check? Who is this most important for?
Speech and processing artefacts Listen back to the processed clip and, where possible, compare it with the original. Adobe and iZotope explain the importance of listening back when editing dialogue. If I want to hear whether noise reduction has affected the speech, I prioritise a reliable listening position. Around 33% of this group are consumers who want to assess speech and processing artefacts first.
Room, desk and listening position Measure the available space and see whether you can position the speakers symmetrically on the left and right. A placement switch can help you make adjustments, but it can’t replace a good setup. With limited space around my screen, I want to know whether I can angle the speakers towards my listening position and set them up symmetrically. Around 27% of this group are consumers who focus mainly on their desk and room.
Connections and complete set Compare the inputs with the outputs on your audio source and check how many speakers are included in the box. Dutch listings for various models are for one speaker each. If I want to use my existing interface and need a stereo pair, I check both the connections and the number of speakers. Around 20% of this group are consumers who place the greatest importance on connections and the cost of a complete set.
Low-frequency hum If a frequency limit is listed, check the dB tolerance too; figures at −3, −6 and −10 dB aren’t directly comparable. Take the room and source file into account. If I also want to check for hum, I look beyond a low frequency figure to the measurement conditions and my listening position. Around 20% of this group are consumers who want to check for low-frequency interference first.

Common buying pitfalls

  • Mistaking one monitor for a stereo pair

    Dutch listings for models including the Genelec 8010A, Yamaha HS5, ADAM Audio T5V and Neumann KH 80 DSP are for one speaker per box. You’ll need two for stereo.

    Remember to budget for connection cables and, depending on your setup, stands.

    Check what’s included in each listing and how many units you need.

  • Comparing the lowest frequency figures without checking the dB tolerance

    A frequency limit at −6 dB isn’t the same as one at −3 or −10 dB. Comparing only the lowest figure can therefore give you a misleading impression.

    Check the dB figure alongside the frequency, and assess low-frequency interference in the context of your room and source file too.

  • Assuming MA 1 equipment is included

    Optional measurement-based calibration for the Neumann KH 80 DSP requires extra equipment and a suitable setup.

    The MA 1 process requires, among other things, an MA 1 measurement microphone, a suitable computer and an audio interface with a balanced microphone input and 48 V phantom power.

    Check these requirements before choosing the KH 80 DSP for its MA 1 calibration.

Brands to consider

Genelec

The 8010A is a compact active monitor for a workspace with limited room. Genelec specifies an XLR input and placement switches.

  • Genelec specifies a lower limit of 67 Hz at −6 dB for the 8010A.
  • The box contains one monitor; the stated frequency limit isn’t an independent listening test.

Yamaha

The active HS5 nearfield monitor has a five-inch woofer, XLR and TRS inputs, and ROOM CONTROL and HIGH TRIM controls.

  • The manual controls give you settings to take into account when positioning the monitor.
  • Yamaha specifies 54 Hz at −10 dB and 74 Hz at −3 dB; the European product listing mentioned is for one speaker.

ADAM Audio

The T5V is an active five-inch nearfield monitor with XLR and RCA connections, according to the Dutch product listing.

  • ADAM Audio specifies 45 Hz at −6 dB for the T5V.
  • The bass-reflex port is on the rear, so allow space behind the cabinet when positioning it. The listing is for one speaker.

Neumann

The KH 80 DSP is designed for compact nearfield setups, with a placement setting and support for optional MA 1 calibration.

  • Neumann describes both the placement switch and the option to use MA 1.
  • MA 1 requires additional measurement and interface equipment. The Dutch product listing is for one monitor.

KRK

According to KRK, the ROKIT 5 Generation Five offers Mix, Focus and Create modes, along with EQ options for different setups.

  • The listening modes and EQ settings provide different adjustment options, according to the manufacturer.
  • These features don’t prove that the monitor makes dialogue editing easier to assess. On 14 October 2026, the Dutch Bax listing said the product was no longer in the range; this doesn’t tell you whether the model is available elsewhere.

Products at Joybuy

Related products coming soon.

Frequently asked questions

How should you position two monitors when listening back to dialogue?

Angle both speakers towards your listening position and aim for similar distances and heights on the left and right. For stereo, Genelec recommends a 60-degree angle at the listening position; then assess the result in your own room.

Can a studio monitor remove noise or artefacts from a recording?

No. A monitor plays back the audio signal; reducing noise and reassessing the processing are part of your audio workflow. Compare the processed clip with the original to check what has changed.

How do you compare the lowest frequency of studio monitors?

Compare frequency limits only alongside their dB tolerance: figures at −3, −6 and −10 dB aren’t directly comparable. The stated limit alone doesn’t tell you what low-frequency hum you’ll be able to assess in your room.

Do you need two active monitors for a stereo pair?

You need two speakers for a stereo pair, even if each monitor has a built-in amplifier. Check how many are in the box and whether the inputs match the outputs on your audio source.

What do you need to calibrate the Neumann KH 80 DSP with MA 1?

The MA 1 process requires additional equipment, including the MA 1 measurement microphone, a suitable computer and an audio interface with a balanced microphone input and 48 V phantom power. Check that the equipment and process are suitable for your setup.