Who are these setups suitable for?

Anyone with just one spare socket for their speakers

If you want to listen in stereo while digitising your tapes, look for sets whose manufacturer specifies one power supply for both speakers. IK Multimedia and ADAM Audio each describe a set configured this way.

Anyone already using an audio interface

Match the speaker inputs to the outputs on your interface and the rest of your recording setup. The D3V has balanced TRS inputs and USB-C; the connection you need will depend on the equipment you already own.

Anyone short on listening space

Measure your available space to make sure both speakers will fit, then angle them towards your listening position. Genelec recommends placing a stereo pair symmetrically, with a 60° angle between the monitors.

What should you look for when choosing?

Stereo set with one documented power supply

Best when: having just one mains connection for the speakers is your top priority.

Check: make sure the analogue inputs and cables you need are compatible with your recording setup.

Two separate active monitors

Best when: you have two suitable mains connections and want to position the monitors separately.

Check: you’ll need two monitors for stereo, with connections for both.

Passive monitor with an amplifier

Best when: you already have a suitable amplifier and can connect it to your setup.

Check: the amplifier needs its own power, so a passive speaker doesn’t make for a completely power-free setup.

What to consider What to look for Who should consider this?
Mains connections Check the set’s power supply, the connection between the left and right speakers, and the power requirements of the rest of your setup. If I want to listen in stereo with few spare sockets, I look for a set with one documented power supply for the speakers. Around 36% of consumers prioritise the number of mains connections needed.
Connections Make a note of the outputs on your cassette deck and audio interface, then check that they match the speaker inputs. If you want to keep using your existing recording setup, you’ll need connections that are compatible with your equipment. Around 29% of consumers give connection compatibility top priority.
Stereo placement Measure the space available for both speakers and angle them towards your listening position. Only compare frequency limits when they use the same measurement tolerance. On a small desk, I want to be able to position both channels without losing sight of my listening position. Around 21% of consumers focus mainly on stereo placement and listening reference.
Complete set Check whether the version includes one speaker or a pair, and whether you’ll need a power supply, connecting cables and possibly an amplifier. If I want to put together a complete stereo set, I check what I need for both channels and what I already own. Around 14% of consumers prioritise having a complete setup.

To record from a cassette deck, you’ll need a suitable line input; a speaker input isn’t a substitute. Audacity recommends using the cassette deck’s line-out, tape-out or record output for your recording setup, where available.

Common buying mistakes

  • Assuming a passive speaker is a complete setup that needs no mains power

    A passive monitor such as the Avantone Mixcube Passive needs a suitable amplifier. The amplifier must also fit into your power plan.

    Think of a passive monitor as part of a setup that includes an amplifier, speaker and the cables you need.

  • Comparing a single monitor with a stereo pair

    The Genelec 8010A is sold individually, while IK Multimedia lists two speakers in the box for the iLoud Micro Monitor.

    Check how many speakers are included in the version on offer, and factor in the mains connections you’ll need for stereo.

  • Connecting a cassette deck to a computer’s microphone input just because the plug fits

    According to Audacity, a stronger line-level signal can overload a microphone input and potentially cause damage.

    Check that your recording setup has a suitable line input and use an appropriate output on the cassette deck.

  • Comparing frequency limits without checking the measurement tolerance

    IK Multimedia lists the iLoud Micro Monitor at 45 Hz at −10 dB; Genelec lists the 8010A at 67 Hz at −6 dB. These figures are based on different measurements.

    Only compare values like these if the measurement tolerance is the same and the specifications mean the same thing.

Brands to consider

IK Multimedia

The iLoud Micro Monitor is a compact stereo set with analogue RCA and 3.5mm inputs.

  • IK Multimedia lists two speakers, one power supply and a connecting cable in the box.
  • The stated lower limit of 45 Hz is at −10 dB, so it isn’t directly comparable with figures at −6 dB.

ADAM Audio

The D3V is an active desktop stereo set with balanced TRS inputs and USB-C.

  • The D3V manual lists one mains cable and power supply for the set.
  • You can’t connect an analogue cassette output directly to the USB-C input; check which input suits your recording setup.

PreSonus

The Eris 3.5 2nd Gen is sold as a pair and has several analogue inputs.

  • PreSonus lists TRS, RCA and 3.5mm inputs.
  • Check the mains connection and what’s included with the version you’re buying before adding it to your socket plan.

Genelec

The 8010A is a compact active monitor sold individually.

  • Genelec lists the dimensions and a mains cable for each speaker.
  • You’ll need two for stereo, so remember to allow for both mains connections.

Avantone Pro

The Mixcube Passive is designed as an additional passive monitor reference.

  • Avantone lists speaker terminals and a specified range of 200 Hz–10 kHz.
  • You’ll need a suitable amplifier; the manufacturer positions this model as an additional reference monitor.

Joybuy products

Related products coming soon.

Frequently asked questions

Should I connect the monitors directly to the cassette deck or to the audio interface?

Route the recording signal through a suitable line input first. Where available, Audacity recommends using the deck’s line-out, tape-out or record output for this. If you’re recording with an audio interface, Focusrite recommends connecting your monitors or headphones to the interface outputs. Check which outputs your devices have.

Can I still listen in stereo if I have just one spare socket?

You can power the speakers with a suitable stereo set whose documentation lists one power supply for both speakers. For the iLoud Micro Monitor, IK Multimedia describes two speakers, one power supply and a connecting cable; the ADAM Audio D3V manual also lists one mains cable and power supply for the set. Your cassette deck and other recording equipment may need power too.

How should I position the monitors for stereo playback?

Angle both monitors towards your listening position and position them as symmetrically as possible. Genelec recommends a 60° angle between the left and right monitors for stereo. Check that your desk and listening space can accommodate this setup.

Can I use an extension lead if I don’t have many sockets?

Don’t connect extension leads to one another. The fire service recommends plugging high-power appliances directly into a wall socket. When planning your monitor setup, remember to allow for the connections needed by the rest of your equipment too.

How do I clean the monitors?

Follow the manual for the model you’ve bought. The ADAM Audio D3V manual says to switch off the system before cleaning any of its components.