Who is this choice relevant for?

Editor with one free socket

You’re looking for a stereo set that doesn’t need a separate mains socket for each speaker, and you’re mindful of the limitations compact monitors may have when assessing deep bass.

Editor assessing bass balance

You want to understand what the stated frequency limit and measurement tolerance tell you, and what else you need to assess at your own listening position.

Editor with a small desk

You need to position two speakers so they fit and connect them to your existing audio outputs, without assuming that a small cabinet will solve room-related issues.

What should you look for when buying?

When editing bass guitar tracks, the number of mains sockets, usable low end, positioning and a complete, connectable set all matter in different ways.

What to consider What to check before buying Especially relevant for
Mains power Check how many speakers are included, which unit needs power and how the speakers connect to each other. If I only have one free socket, I want to know how many connections the complete set needs. Around 36% of consumers prioritise the number of mains sockets required.
Low-end response Look for the dB tolerance at the lowest frequency; −3 dB and −10 dB are not directly comparable measurement points. Assess the bass balance using a second listening reference too. When editing bass guitar, I want to know what the monitor lets me hear in the low end, not just its lowest Hz figure. Around 29% of consumers give usable low-end response top priority.
Positioning Measure whether two speakers will fit symmetrically on your desk and can be angled towards your listening position. With a small desk, I want to position two speakers properly without the room affecting my judgement of the bass. Around 21% of consumers prioritise positioning and the effect of the room.
Connections and what's included Compare the inputs with your audio interface, and check whether the version includes one speaker or a pair and which cables are included. I want to connect my audio output and have a complete stereo pair, rather than having to make a second purchase. Around 14% of consumers give connections and what's included top priority.

Pitfalls to avoid

  • Treating the lowest frequency as a direct measure of performance

    The specifications for the Yamaha HS4, IK iLoud Micro Monitor and ADAM T7V use different dB tolerances. The room also affects what you hear at your listening position.

    Read the dB tolerance alongside the Hz figure, and check the bass balance at your own listening position too.

  • Mistaking a single monitor for a stereo set

    A single speaker isn’t a complete stereo pair. You need two ADAM T7V units for stereo; the Yamaha HS4 is described as a set of two.

    Check how many speakers are included in the exact version before assessing your stereo setup.

  • Assuming passive means a complete setup without mains power

    A passive Avantone MixCube needs a suitable amplifier. Its stated frequency response starts at 200 Hz, so this model isn’t a main reference for deep bass guitar low end.

    Choose this option only if you already have a suitable amplifier, the right connections and a mains socket available for it.

Relevant brands to consider

Yamaha

Yamaha describes the HS4 as a compact stereo set with connections on the left speaker and a cable to the right speaker.

  • Yamaha specifies analogue inputs and room controls for the HS4.
  • The stated lower limit is 83 Hz at −3 dB; this figure alone doesn’t give you a complete picture of deep bass guitar low end.

IK Multimedia

IK Multimedia describes the original iLoud Micro Monitor as a compact pair of speakers with one power supply and a cable between the speakers.

  • The manufacturer lists RCA and 3.5 mm connections, along with acoustic settings.
  • The stated low-frequency limit is 45 Hz at −10 dB. This measurement tolerance isn’t the same as a −3 dB specification.

PreSonus

PreSonus describes the Eris 3.5 2nd Gen as a compact pair with analogue inputs, a headphone output and acoustic controls.

  • PreSonus lists balanced 6.35 mm TRS inputs and unbalanced RCA and 3.5 mm stereo inputs.
  • The manufacturer lists 80 Hz–20 kHz without a dB tolerance at the limit; don’t use this for a direct comparison with limits that do state a tolerance.

ADAM Audio

ADAM Audio describes the T7V as a nearfield monitor with its own power supply, for a setup with room and power for two speakers.

  • ADAM Audio specifies 39 Hz at −6 dB for the T7V.
  • You need two units and two mains sockets for stereo; the manufacturer’s specification isn’t a measurement at your listening position.

Avantone Pro

Avantone Pro describes the passive MixCube as an additional mono reference for anyone who already has a suitable amplifier.

  • Avantone Pro lists a nominal impedance of 8 ohms and a recommended amplifier power of 10–200 W.
  • The stated frequency response is 200 Hz–10 kHz, which means the MixCube isn’t a main solution for assessing deep bass guitar low end.

Joybuy products

Related products coming soon.

Frequently asked questions

Do you need passive monitors if you only have one free socket?

No. A set such as the Yamaha HS4 or original IK Multimedia iLoud Micro Monitor connects the second speaker to the unit with a built-in power supply. Passive speakers don’t have their own mains plug, but they do need a suitable amplifier, which uses power.

How should you position speakers to assess bass guitar tracks?

Start with the left and right speakers at the same height and an equal distance from your listening position. Genelec explains that moving them can reduce the effect of room modes, so a manufacturer’s specification is no substitute for an assessment at your own listening position.

Can a subwoofer make up for the limited low end of a compact set?

A subwoofer can add extra low end, but it needs space, power and careful setup. In its connection advice for the Eris Sub8, PreSonus warns that overlap between the subwoofer’s low end and that of the main monitors can boost or cancel out frequencies. So don’t add one automatically.

Is CE marking compulsory for electrical monitors in the Netherlands?

The Netherlands Food and Consumer Product Safety Authority states that CE marking is compulsory for electrical products placed on the market in the Netherlands. Check the marking and documentation for the specific version; CE marking isn’t a performance test to show that a product is suitable for your bass mix.

Can you simply use an extension lead if you don’t have many sockets?

First check the connected load and the devices’ instructions for use. The Netherlands Fire Service advises fully unwinding cable reels and plugging high-power appliances directly into a socket where possible. This advice isn’t specific approval for any particular extension lead.