Who is this for?

Guitarist recording with a microphone

You want to hear your guitar, backing track and perhaps a click track without unnecessary sound leaking into the recording microphone. RTINGS.com describes closed-back headphones as better suited than open-back models to limiting leakage while recording.

Guitarist using an audio interface

You want to hear your guitar signal as you play, without distracting delay. Focusrite describes direct monitoring as a way to listen to the input signal with virtually no delay. Check which monitoring features your interface offers.

Guitarist mixing recorded takes

You assess recorded guitars and stereo placement after playing, and weigh isolation against an open listening design. Sennheiser presents the open-back HD 490 PRO for critical mixing; this type of design is less suitable for limiting leakage during microphone recording.

What should you look for when choosing?

First decide whether you’ll be recording with a microphone at the same time or mainly mixing afterwards. Then check whether your interface can drive the headphones and which monitoring route you’ll use.

What to consider What should you check? Who is this important for?
Isolation while recording A closed-back design and a good fit can help limit leakage. Test what your microphone actually picks up at your usual playback volume; RTINGS.com describes closed-back models as leaking less than open-back ones. If I’m recording with a microphone, I want to hear a backing track or click track without unnecessary leakage into the take. For around 33% of consumers, limiting leakage is the top buying priority.
Playing along without distracting delay Check whether your interface offers direct monitoring and whether software monitoring is active at the same time. According to Focusrite, direct monitoring sends the input signal to the headphone output with virtually no delay. If I’m playing through an interface, I want to hear my playing in time. Around 27% of consumers prioritise monitoring without distracting delay.
Checking your mix Decide whether you’ll mainly be listening back afterwards in a quiet room. An open-back design lets sound in and offers less isolation from ambient noise; Sennheiser describes the open-back HD 490 PRO as a model for critical mixing. If I’m assessing recorded takes and stereo placement without recording with a microphone at the same time, an open listening design could be a good fit. Around 20% of consumers make mix checking their top priority.
Fit and maintenance Try the fit for yourself and check whether cables and ear pads are replaceable on the exact model. Manufacturers list these features for certain models from beyerdynamic, Audio-Technica, Sennheiser and AKG, for example. If I’m having long sessions, I want my headphones to feel comfortable and to be able to replace worn parts. For around 20% of consumers, fit and maintenance come first.

Common buying mistakes

  • Trying to fix delay by changing headphones alone

    The delay may be caused by listening to the input signal through your recording software. Changing your headphones won’t automatically change that monitoring route.

    First, try direct monitoring if your interface has this feature. If you hear the signal twice, check whether software monitoring is also switched on; Focusrite advises against using both monitoring methods at once.

  • Assuming an open-back or semi-open design isolates as well as a closed-back model

    Open-back and semi-open models let sound through. When recording with a microphone, this can cause an audible backing track or click track to end up in the recording.

    Decide whether you’ll be recording with a microphone at the same time or mainly mixing afterwards. If in doubt, check for leakage in your own setup.

    If the backing track gets picked up by the microphone, you may need to record the take again.

  • Choosing a DT 770 PRO variant based on the model name alone

    beyerdynamic distinguishes between the intended uses of the 32-, 80- and 250ohm versions. Suitability also depends on the headphone output of your interface.

    Check the full variant name, impedance and specifications of the output you plan to connect the headphones to.

  • Confusing the manufacturer’s warranty with all your statutory rights

    The Dutch government states that the Netherlands has no fixed statutory guarantee period. If a product is faulty, the seller is your point of contact.

    Keep your proof of purchase and check the warranty terms alongside your statutory rights; a manufacturer’s warranty does not automatically replace those rights.

Brands to consider

Audio-Technica

The closed-back ATH-M50x is an option if you want headphones for recording with a detachable cable.

  • Audio-Technica says this model has over-ear pads, comes with three cables and includes a 6,3mm adapter.
  • Check the fit in your own setup; these features don’t guarantee that every microphone will avoid picking up sound from the headphones.

beyerdynamic

The closed-back DT 770 PRO comes in different impedance versions. Choose one to suit the headphone output you’ll be using.

  • For the DT 770 PRO 80 ohm, beyerdynamic lists replaceable ear pads and a 3,5mm plug with a 6,35mm adapter.
  • According to beyerdynamic, the 32-, 80- and 250ohm versions are intended for different uses. Check which variant suits your interface.

Sennheiser

The range includes closed-back models such as the HD 280 PRO and HD 480 PRO, as well as the open-back HD 490 PRO for checking your mix.

  • For the HD 280 PRO, Sennheiser lists replaceable ear pads and a wired 3,5mm connection with a 6,3mm adapter.
  • Sennheiser positions the open-back HD 490 PRO for critical mixing. An open-back design is less suitable for limiting leakage during microphone recordings.

AKG

The semi-open K240 Studio is worth considering if you mainly listen back to recorded material and don’t need maximum isolation.

  • According to AKG, the K240 Studio has a detachable cable with a mini-XLR connection and replaceable ear pads.
  • A semi-open design isn’t necessarily suitable for sensitive microphone recordings with loud backing tracks.

Sony

Sony Netherlands presents the MDR-7506 for recording and studio use.

  • For the MDR7506.EU, Sony Netherlands lists a 3 m cable and a weight of 230 g, among other specifications.
  • Check whether the cable length is practical in your home studio; these specifications don’t tell you how comfortable the headphones are to wear.

Joybuy products

Related products coming soon.

Frequently asked questions

Will new studio headphones fix delay when playing guitar?

Not necessarily. First, check your monitoring route: direct monitoring on a compatible interface sends the input signal to your headphones with virtually no delay. If you hear the signal twice, check whether software monitoring is also active.

Which plug and parts should I check before use?

Compare your interface’s headphone output with the plug and any adapter supplied with the exact model. Also check whether replacement cables or ear pads are available. According to their manufacturers, the ATH-M50x and K240 Studio have detachable cables, but they don’t necessarily use the same connection.

Can I use open-back headphones while recording guitar with a microphone?

Yes, but if you’re using an audible backing track or click track, a closed-back design is usually better for limiting leakage into the microphone. An open-back model is more suited to checking your mix in a quiet room when you’re not recording with a microphone.

What cooling-off period and warranty apply to online purchases in the Netherlands?

When you buy online from a business, you’ll usually have a 14-day cooling-off period; check the applicable exceptions and terms. You’re also entitled to a product that works as it should. The Dutch government states that the Netherlands has no fixed statutory guarantee period, and that you should contact the seller if a product is faulty.