Listeners with existing passive speakers
You want to know whether a new amplifier can drive your speakers appropriately from your listening position. Start with the speaker specifications.
For chamber music in a large living room, choose a stereo amplifier based on your passive speakers, listening distance and preferred sources – not just the size of the room or a wattage figure. Start by comparing the speaker specifications and permitted load. Then decide between separate sources, built-in streaming and any upgradeable room correction; none of these replaces carefully positioning your speakers.
You want to know whether a new amplifier can drive your speakers appropriately from your listening position. Start with the speaker specifications.
With chamber music, you prioritise a clear stereo image and want to take speaker placement and reflections in your living room into account too.
You’re choosing between an existing separate source and streaming through the amplifier. Connections, controls and any room-correction features all play a part.
Start by checking that the amplifier is a good match for your speakers. Then decide which sources you want to connect, and only after that consider whether a room-calibration feature suits your setup.
| What to consider | What to look for | Who should pay particular attention? |
|---|---|---|
| Speaker compatibility | Check impedance, sensitivity and permitted load. Only compare continuous power ratings when the impedance and measurement conditions are the same. Yamaha specifies 100 W + 100 W at 8 ohms, 20 Hz–20 kHz and 0.07% THD for the R-N800A. | If you want to drive your existing passive speakers appropriately from your listening position, this is your first compatibility check. Around 31% of consumers put the speaker-amplifier match first. |
| Stereo image in the room | First compare speaker and listening-seat positions in your own room. Then decide whether you want the specific calibration feature offered by a model. Yamaha’s technical guidance explains how reflections can affect the perceived position of instruments. | If you want to hear individual instruments clearly positioned from your listening spot, the room and setup matter as well as the amplifier. Around 25% of consumers prioritise the stereo image in the room. |
| Connections and sources | Make a note of the outputs on your existing sources and check that the amplifier has the corresponding inputs. Decide whether you need network playback built into the unit. | If you want to use a computer, turntable or another existing source, check that the relevant connections are available. Around 19% of consumers put source options and controls at the top of their list. |
| Overall setup | Include any separate sources and add-ons you’ll need. According to NAD, the optional MDC2 BluOS-D module is required for BluOS streaming and Dirac Live on the NAD C 389. | If you want to keep a complete setup within your budget, focus on the features you actually need and any optional extras. Around 13% of consumers prioritise the total cost of their setup. |
| Service and product information | Check who the seller is and review the documentation, safety information and CE marking for the specific version. Equipment within the scope of the EU Low Voltage Directive, including equipment rated at 50–1000 V AC, is subject to the relevant conformity requirements. | If you want to know in advance who the seller is and what to expect if something goes wrong, check these details before you buy. Around 12% of consumers give service and purchase information top priority. |
A figure specified at 4 ohms is not directly comparable with continuous power at 8 ohms. What matters is still how well the amplifier matches the connected speakers.
Compare power per channel at the same impedance and under the same measurement conditions, and check the permitted speaker load.
Reflections can affect the stereo image, but a correction feature won’t remove the need to choose suitable speaker and listening positions.
First assess your setup in the room, then check what the model’s specific feature does and whether it’s included.
Connections vary by model. Yamaha doesn’t list HDMI ARC for the R-N800A, while Marantz lists HDMI ARC for the MODEL 40n.
Before you buy, make a list of the outputs on your sources and compare them with the inputs on the exact model you’re considering.
The R-N800A is a network stereo amplifier for anyone looking for streaming and YPAO calibration in one unit.
The C 389 is an integrated amplifier for anyone who wants digital inputs and the option to add features later.
The MODEL 40n combines music playback through HEOS with HDMI ARC, making it an option if you also want to connect your TV.
The PMA-1700NE is an integrated amplifier for existing digital and analogue sources.
The CXA81 Mk II is an alternative with digital inputs for anyone using a separate music source.
No. Assess the combination based on your speakers, listening distance and power ratings specified on a comparable basis – with the same impedance and measurement conditions. Room size alone doesn’t determine a universal wattage threshold.
Don’t assume you can: active speakers have their own amplification. Check which type of signal input they require and only use a suitable output on your chosen amplifier.
First compare the position of both speakers and your listening seat in your own room. Reflections can affect the perceived position of instruments, so a calibration feature doesn’t replace this assessment.
No. According to NAD, the optional MDC2 BluOS-D module is required for the BluOS upgrade and Dirac Live room correction described. Check which module and licence are included with the specific version.
No. According to an explanation from the Dutch Consumers’ Association dated 16 September 2026, the Netherlands has no fixed statutory guarantee period; what matters is what you can reasonably expect from the product. If a fault isn’t your responsibility, the seller may be obliged to repair or replace the product free of charge.