Makers with a wide collage board
You want to show the whole piece in a single overview photo and need even lighting right to the edges. DT Heritage describes two lights at around 45° as a common setup for photographing flat work.
For a wide, mostly flat collage board, two diffused light sources positioned evenly are a good starting point. For a smaller piece, one adjustable light may be enough, provided a test shot shows no fall-off in brightness. DT Heritage describes two lights at around 45° as a common setup for photographing flat work. Check for reflections and shadows on glossy or raised areas, and make sure separate components are compatible before buying.
You want to show the whole piece in a single overview photo and need even lighting right to the edges. DT Heritage describes two lights at around 45° as a common setup for photographing flat work.
You want to capture paper colours accurately and check whether reflections obscure details in foil, varnish or glue. Canon Europe emphasises that the white balance should match the lighting conditions.
You already have a light source and are looking for a compatible light modifier rather than automatically buying a complete kit. For example, Godox and SmallRig describe products with a Bowens mount; check that it also fits your light.
Choose this if: you want to light a wide board for a single overview photo and have space for a light on each side.
Bear in mind: the space needed for setup, and the exact contents, fittings and power supply included with the kit.
Choose this if: you photograph smaller boards or details and want to adjust the light position regularly.
Bear in mind: a single light still needs to illuminate the far edge of the work evenly. Check this with a test shot.
Choose this if: you already have a compatible light source and want a larger, diffused light surface.
Bear in mind: a softbox without a light source will not produce any light. Also check the mount and whether your stand can support it.
Measure the board and use a test shot to check both the centre and the corners. Glossy or raised areas may need the light to fall differently from a flat overview photo.
| What to consider | What to look for | Who should pay particular attention? |
|---|---|---|
| Even coverage | Measure the board and check whether lights can stand outside the frame on either side. Compare the centre and corners in a test shot. | If I want to show the entire wide board in one photo, I want the centre and edges to be evenly lit. Around 36% of consumers give full-board coverage the highest priority. |
| Consistent colour | Use the same lighting settings for similar pieces and check the white balance in a test shot. | I want to keep paper and paint colours consistent between shots. For around 29% of consumers, colour consistency is the most important buying priority. |
| Gloss and texture | Check for reflections and shadows in a test shot. Move the lights or take a separate detail photo. | On glossy or raised areas, I want to assess reflections without losing the texture. Around 21% of consumers rank this above other buying priorities. |
| A complete, compatible kit | Compare the contents list with what you already own, and check the mount, power supply and number of stands included. | If I do not want to combine components myself, I want to know in advance whether the lights and accessories are compatible. For around 14% of consumers, a complete, compatible setup is the top priority. |
A light modifier such as the SmallRig LA-O90 is not a light source. A separate softbox cannot light a collage board on its own.
Read the contents list and check whether the light, stand and any second light source are included, as well as which mount they use.
You may need a compatible light or a suitable stand in addition to the softbox to create a working setup.
Different fittings are listed for the NEEWER NK103: the European manufacturer's page specifies E26, while a Dutch product listing states E27 and 230 V. Do not assume these are the same electrical version without confirmation.
Before buying, ask for the exact model, the lights included, the fitting, the mains power details and the product information that applies to the version you will receive.
DT Heritage distinguishes between even lighting for photographing flat work and raking light to emphasise texture. One setup may not be suitable for both purposes.
First, take an evenly lit overview photo. To show visible layers, adjust the lighting angle and take a separate detail photo if needed.
Separate continuous lights for a modular setup with a compatible light modifier.
Separate softboxes, including the LA-O90, for those who already have a compatible light.
Complete softbox kits as an alternative to sourcing lights and modifiers separately.
Softboxes for specific light ranges, when you know the mount on your existing light source.
Start with two light sources positioned similarly on either side of the board. DT Heritage describes around 45° as a common starting setup for photographing flat work. Adjust the position if a test shot shows reflections.
No. A CRI value alone does not guarantee an accurate colour photo. Canon Europe points out that the white balance should be set for the lighting being used, so check the colours in a test shot.
Check that the softbox fits your light and that the stand can support the combination. Follow the light's instructions and check the contents list to see whether a light source is included. The SmallRig LA-O90, for example, is a light modifier, not a light.
No, this does not automatically apply to every purchase for a webshop. Business.gov.nl states that a 14-day cooling-off period generally applies to qualifying online consumer purchases, and clarifies that business purchases are not covered by the same consumer rights. For a business order, check the seller's contract and returns terms.
Not automatically for every component. According to the European Union's Your Europe, CE marking is only compulsory for products covered by the relevant harmonised EU rules. Assess the electrical light and the passive softbox separately. CE marking is a declaration by the manufacturer, not a certificate from a central EU body.