Who is this setup for?

Maker with glossy samples

You want to show both the gloss and surface texture, and need control over where the softbox is reflected in the glaze. Broncolor highlights the importance of light-shaper positioning when photographing glossy subjects.

Ceramicist comparing samples

You want to photograph successive glaze samples under similar lighting, so you’re looking for a repeatable setup and a suitable white balance. Canon Europe explains that white balance affects colour reproduction under different lighting conditions.

Photographer short on table space

You need to fit the light, camera and piece on a small table, then pack everything away afterwards. A compact separate softbox and a foldable light tent each need different amounts of space for positioning the light and choosing your shooting angle.

What should you look for when choosing?

Separate softbox with a suitable light

A good fit if: you already have a compatible studio light and want to adjust the direction of reflections for each sample.

Bear in mind: the softbox doesn’t produce light on its own; check the light, fitting and stability of the setup too.

Compact light tent with built-in lighting

A good fit if: you photograph small samples in a fixed tabletop setup and want to avoid a separate studio light.

Bear in mind: your sample, background and preferred camera angle all need to fit inside the tent and through its openings; there’s less flexibility to adjust the light position.

Adjusting your existing diffused light

A good fit if: your current lighting is adequate and you mainly want to move an unwanted reflection.

Bear in mind: changing ambient light needs extra attention if you want to photograph several samples under similar conditions.

What to consider What should you check? Who is this most important for?
Gloss and texture Can you move the light and diffuser? Take a test shot and assess both the reflections and the glaze detail. If I want to show the gloss without letting it overpower the texture, I need to be able to adjust the light position. Around 36% of consumers put controlling reflections first.
Colour consistency between samples Can you repeat the lighting setup and camera settings, and set the white balance to suit? When I compare different glaze samples, I want to minimise changes in lighting and colour casts. Around 29% of consumers make colour consistency their top priority.
Space and storage Measure your table and the piece. For a tent, check the internal space and shooting openings; for a softbox, make sure there’s room for the light and stand too. When my table is short on space, I want to know whether the whole setup will fit and can be put away afterwards. Around 21% of consumers focus mainly on the space required and storage.
Light and fitting Check that the fitting is compatible with your light, and whether the light, stand and any necessary accessories are included in the set. If I’m considering a separate softbox, I want to know whether I can use it with my existing light and what else I’ll need. Around 14% of consumers start by checking compatibility and the complete setup.

Common buying mistakes

  • Assuming a separate softbox is a complete lighting kit

    A separate light shaper may have a specific fitting, but it won’t necessarily work as a complete light. You’ll need a suitable light and a stable setup as well.

    You may also need a compatible light, a stand or an adapter ring. Check what you already own and what’s included in the box.

    Compare the fitting and the contents list with your existing equipment before ordering.

  • Trying to eliminate all the gloss

    On a glossy surface, reflections can help show shape and shine, but poor light positioning can also hide detail. Broncolor highlights the importance of light-shaper positioning when photographing glossy objects.

    Move the diffused light and take a test shot to assess both the bright areas and the glaze texture.

  • Choosing a light tent by its external dimensions alone

    Your sample, background and preferred shooting angle also need to fit inside the shooting area and through the available openings.

    Measure the whole setup and check the internal dimensions and shooting openings before choosing.

Brands to consider for this setup

Godox

Godox lists the SB-FW6060 as a rectangular 60 × 60 cm softbox with a Bowens mount.

  • The stated size and mount make it easier to check whether the light shaper will suit your light and tabletop setup.
  • It’s a separate softbox, not a complete lighting kit; the specifications don’t say anything about the quality of photos of ceramic glaze.

SmallRig

SmallRig describes the RA-D55 as a separate 55 cm softbox with a Bowens mount, two diffusion layers and a grid.

  • The listed components give you options for this light shaper; check that it’s compatible with your light.
  • You’ll also need a suitable light and enough room for the setup.

NEEWER

According to NEEWER, the LP40 combines a foldable 40 × 40 × 40 cm light tent with built-in dimmable lighting.

  • The fixed tabletop setup could work if your sample and preferred camera angle fit inside the tent.
  • The tent’s design and openings limit your camera angle and where you can position the light. The stated CRI 97+ is a manufacturer specification, not an independent colour test of glaze photos.

Nanlite

Nanlite describes the Rapid 60 as a separate softbox with an FM mount and a Bowens speed ring included.

  • The manufacturer lists two diffusers and a grid for this model.
  • Check that the fitting is compatible with your specific light, and see which components are included in the set on offer.

broncolor

broncolor offers separate softboxes for product photography. For one 60 × 100 cm model, the manufacturer lists a range of available speed rings.

  • broncolor’s demonstrations show why light-shaper positioning matters when photographing glossy subjects.
  • According to the manufacturer, the speed ring for the softbox mentioned isn’t included. The 60 × 100 cm size may take up a lot of room on a small table.

Joybuy products

Related products coming soon.

Frequently asked questions

Do I need to buy two lights straight away for a glossy sample?

No. Start by moving a single diffused light, and try using a reflector to lighten the shadow side if needed. Broncolor highlights the importance of light-shaper positioning when photographing glossy objects; assess the setup with one of your own samples.

How can I keep the colours of different glaze samples consistent?

Keep the lighting setup and camera settings as consistent as possible, and check the white balance under the light you’re using. Canon Europe explains that white balance affects colour reproduction under different lighting conditions; a softbox alone can’t guarantee an exact colour match.

What should I consider when setting up and packing away?

Before you start, check that your sample, table and preferred camera position will all fit. According to NEEWER, the LP40 has openings at the front and top and the tent folds away. With a separate softbox, you’ll also need a suitable light and a stable setup.

What extra items might I need with a separate softbox?

You may need a suitable light and a stand. Check the fitting and what’s included in the box too: SmallRig describes the RA-D55 as coming with diffusers and a grid, while broncolor states that a speed ring isn’t included with the 60 × 100 cm softbox.

Does electrical photography lighting sold in the Netherlands need a CE marking?

CE marking is required for products covered by applicable harmonised EU rules that require it. The European Commission says CE marking isn’t required or permitted for every product, so assess the electrical light or power supply under the rules that apply to that product. A fabric softbox without electronics isn’t automatically subject to the same marking requirement.