Who is this guide for?

Presenters with weak Wi-Fi by the screen

You need to reach one presentation room and can position a repeater where the router’s signal is still usable. TP-Link recommends placing it roughly halfway between the router and the area with poor reception.

Presenters with no shelf space

You’re looking for a device that plugs into a socket, but you’ll also need to check there’s enough room for its casing and any aerials. FRITZ! and devolo both describe plug-in models designed for this type of placement.

Presenters who cast wirelessly to a screen

You need more than just better coverage: check that the sending device can find the receiving screen on the local network. Google Streaming Help explains this network requirement for Google Cast.

What should you look for when choosing?

Plug-in repeater

Choose this if: you need to reach one weak spot, can’t run an Ethernet cable and can find a socket with usable reception.

Bear in mind: the repeater still needs to receive a usable signal from the router, and it takes up space at the socket.

Access point via Ethernet cable

Choose this if: you can run a cable to the presentation room and the specific device has an access point mode.

Bear in mind: installation requires a cable, suitable connections and a suitable spot for the device.

Check your existing network first

Check this first if: the screen isn’t showing up, even though Wi-Fi reception seems adequate.

Bear in mind: extending your coverage won’t automatically fix a device discovery or network settings issue.

What to consider What to look for Who this matters to
Coverage by the screen Test sockets between the router and the presentation room. Don’t choose a spot where the repeater itself gets barely any signal from the router. If I need a stable connection by the screen, I’ll first look for a spot where the repeater can still receive a signal from the router. Around 33% of consumers prioritise coverage above all else.
Space around the socket Check the dimensions, any aerials and the space around neighbouring sockets. If I don’t want to use a shelf, the device still needs to fit physically in the chosen spot. Around 25% of consumers mainly want to save space.
Casting to the screen Check the casting functionality of both the sender and receiver, and test whether they can find each other on the same local Wi-Fi network. Google Streaming Help explains this requirement for Google Cast. If I want to present wirelessly, my device needs to be able to find the screen, and both devices must support the required casting functionality. Around 25% of consumers prioritise casting compatibility above all else.
Wired backhaul Check whether you can run a cable to the chosen spot and whether the specific device has an access point mode and the required Ethernet port. If I can run an Ethernet cable to the extension point, I can consider a suitable access point setup. Around 17% of consumers mainly want a wired connection to the extension point.

Common buying mistakes

  • Plugging in the repeater where the signal is weakest

    A repeater can only pass on the signal it receives from the router where it’s placed. So putting it right by the screen won’t help if the signal is already too weak there.

    First, try possible sockets between the router and the screen, then check the connection in the presentation area.

  • Confusing a Wi-Fi repeater with a presentation receiver

    A repeater extends a network connection, but it won’t give a laptop casting functionality by itself. For Google Cast, the sending device needs to be able to find a suitable receiver on the same Wi-Fi network.

    Check the casting functionality of both the sending device and the screen. You may need a suitable receiver or a different connection.

  • Assuming every mesh feature works with every router

    The mesh feature described may depend on a compatible router or a specific hardware version. Seeing the word ‘mesh’ on the packaging doesn’t tell you whether it will work with your network.

    Before buying, check router compatibility and the hardware version of the exact model.

Brands to consider

FRITZ!

FRITZ! describes the FRITZ!Repeater 1200 AX as a compact Wi-Fi 6 model with one gigabit LAN port. The mesh integration mentioned is designed for a FRITZ! network.

  • The manufacturer’s specifications make this model worth comparing if you have limited shelf space or need a LAN connection.
  • Don’t assume the same mesh features will work with every router; check the exact version and compatibility.

TP-Link

The Dutch product information describes the RE705X as featuring Wi-Fi 6, an Ethernet port and access point mode. Documentation for the RE705X(EU) V2 mentions EasyMesh with a compatible router.

  • Access point mode gives you the option of a wired setup if you can run an Ethernet cable.
  • Check the hardware version and router compatibility; the mesh information differs between the product details and V2 documentation.

devolo

devolo describes the WiFi 6 Repeater 3000 as a plug-in model and lists a gigabit Ethernet port in its documentation.

  • Worth comparing if you don’t want to use a shelf and may need a wired connection.
  • The stated transfer speed is a manufacturer’s specification, not a measured result for presentations. Also check that the casing will fit at the intended socket.

Products at Joybuy

This product selection includes a mesh system, a plug-in repeater and wired access points, giving you different ways to extend Wi-Fi to a presentation room. For each model, check that the setup suits your available space, cabling and network requirements.

TP-Link Deco E4 mesh Wi-Fi system, 3-pack

TP-Link Deco E4 mesh Wi-Fi system, 3-pack

An option if you want to extend Wi-Fi with several mesh units rather than adding a single repeater.

3-pack with dual-band Wi-Fi on 2.4 and 5 GHz and Wi-Fi 5 (802.11ac). According to the product description, each unit has two Ethernet ports.

View at Joybuy
TP-Link Omada EAP653 Wi-Fi 6 access point

TP-Link Omada EAP653 Wi-Fi 6 access point

Suitable for a wired setup if you can run an Ethernet cable to the required location.

Dual-band Wi-Fi on 2.4 and 5 GHz and a gigabit Ethernet port. The product description mentions PoE+; the PoE setup described requires a suitable power supply.

View at Joybuy
TP-Link EAP725-Wall Wi-Fi access point

TP-Link EAP725-Wall Wi-Fi access point

A wired access point to consider if wall or ceiling installation suits your setup.

The product description mentions dual-band Wi-Fi on 2.4 and 5 GHz, three Ethernet ports and PoE. The installation described uses PoE and requires suitable cabling and a power supply.

View at Joybuy
WiFi Repeater Pro Black

WiFi Repeater Pro Black

A plug-in repeater to compare if you want extra coverage without putting a device on a shelf.

The product description lists two external aerials, 2.4 GHz connectivity and dimensions of 80 × 54 × 70 mm. No 5 GHz band is listed.

View at Joybuy
TP-Link TL-WA801N access point and Wi-Fi extender

TP-Link TL-WA801N access point and Wi-Fi extender

An option if you’re looking for a device with both access point and extender modes, and a wired setup suits your needs.

The product description lists 2.4 GHz, up to 300 Mbit/s, two external aerials and Passive PoE. No 5 GHz band is listed; check that the PoE setup is suitable.

View at Joybuy

Frequently asked questions

Can a Wi-Fi repeater send my presentation to the screen by itself?

No. A repeater extends a network connection, but it doesn’t send the presentation to the screen itself. For Google Cast, you’ll also need a suitable receiver, and the sending device must be able to find it on the same Wi-Fi network.

Where should I put a repeater if I don’t have any shelf space?

Find a free socket between the router and the area with weak Wi-Fi where the repeater can still receive a usable signal from the router. Check that the casing and any aerials will fit, too; don’t choose a spot just because it’s close to the screen.

What can I do if wireless extension doesn’t work where I need it?

If you can run an Ethernet cable from the router, an access point with a suitable access point mode could be an alternative. Check the connections and mode of the exact version before choosing.

What should I look for in the CE marking on a Wi-Fi device?

According to the Dutch Authority for Digital Infrastructure, radio equipment that meets the applicable European requirements must carry a CE marking. Check the marking and documentation for the version you’re actually buying; a retailer’s product description isn’t, by itself, a declaration of conformity.

What warranty applies when buying in the Netherlands?

According to the Dutch government, you’re entitled to a product that works as it should, but there is no fixed statutory warranty period that applies equally to every product in the Netherlands. If a product is faulty, you may be entitled to a free repair, replacement or refund. Any additional manufacturer’s warranty is separate from this.