Who is this for?

Standing editor with one pair of monitors

You want to control the volume, mute and mono settings without reaching for your audio interface or DAW, even when you raise the desk.

Bass editor with a subwoofer

You want to compare bass parts with and without a subwoofer. Bear in mind that speaker placement and listening position can affect what you hear; Genelec explains how the room can colour the perceived sound.

Editor with multiple monitoring options

You switch between pairs of speakers or headphones, so you need more outputs and level controls than a single volume knob can offer.

What should you look for?

Start with the controls you want within easy reach while you work. Then decide whether you need mono, a switchable sub output, or extra speaker and headphone outputs.

What to consider What should you check? Who is this important for?
Controls within easy reach Check where the controller sits at both desk heights, which controls are on the front panel, and whether your interface’s output matches its input. If I want to adjust the volume or quickly mute the sound while standing, I need controls that remain within reach at both desk heights. Around 36% of consumers prioritise these everyday controls.
Checking bass in mono Check whether the specific model has a mono switch; a mono or sub output is not automatically the same feature. If I want to check bass parts in mono quickly, a dedicated mono switch is useful. Around 29% of consumers prioritise this check.
Listening with and without a subwoofer Check whether the subwoofer can be connected to the output, where the crossover is, and whether you can switch off the sub without muting the main speakers. If I want to compare the sound with and without a subwoofer while editing, a separately switchable sub output is important. Around 21% of consumers prioritise this comparison.
Multiple monitoring options Count the stereo outputs and headphone connections you need. Also check whether you need separate level controls, cue or talkback. When I switch between several speakers or pairs of headphones, I want enough suitable outputs and controls. Around 14% of consumers prioritise multiple monitoring options.

Common mistakes

  • Assuming a mono output has a built-in subwoofer crossover

    A full-range mono output won’t automatically filter the signal for a subwoofer. Check the crossover too, as well as the effect of your listening position; Genelec explains how the room can affect the bass you hear.

    Check where the crossover sits in your audio system, then compare the sound with and without the subwoofer from your usual listening position.

  • Expecting a passive volume controller to power headphones

    Speaker volume control and a powered headphone output are two different features. According to its product specifications, the Mackie Big Knob Passive is a passive controller, so don’t assume it can drive headphones.

    Use your interface’s headphone output, or check that the controller you choose has its own headphone output.

  • Confusing a monitor controller with a USB audio interface

    According to PreSonus, the USB-C connection on the PreSonus MicroStation BT is for power only and does not carry audio from a computer.

    Before you buy, check whether the exact model handles audio over USB or only routes analogue signals.

Brands to consider

Mackie

The Big Knob Passive is designed for hands-on volume control and switching between sources and pairs of monitors. Big Knob Studio adds a USB recording interface.

  • Mackie specifies two sources and two pairs of monitors for the Big Knob Passive, with mono, dim and mute controls.
  • The passive version has no built-in headphone amplifier or separate subwoofer output.

PreSonus

The MicroStation BT is designed for one pair of monitors with a switchable subwoofer output; the Monitor Station V2 is designed for multiple pairs of speakers and headphones.

  • According to PreSonus, Sub Bypass on the MicroStation BT mutes the subwoofer without switching off the full-range speakers.
  • The USB-C port on the MicroStation BT is for power only. The Monitor Station V2’s features are not automatically available on the MicroStation BT.

Palmer

The MONICON XL is designed for a more extensive analogue monitoring setup with multiple pairs of monitors and mono monitoring.

  • Palmer specifies three pairs of speakers, two headphone outputs, a correlation meter and a mono-summed output.
  • The mono output is full-range and is not specified as a built-in subwoofer crossover.

Audient

The Nero is designed for setups with multiple sources, pairs of speakers and headphones, as well as an assignable sub output.

  • Audient specifies three stereo speaker outputs, four headphone outputs, and mono and polarity controls.
  • If you only use one pair of speakers, the extra routing may offer more features than you need.

SPL

The 2Control is designed for anyone who works with two pairs of headphones and adjustable crossfeed as well as speakers.

  • SPL specifies two stereo sources, two pairs of speakers, two headphones and a mono output.
  • Crossfeed is no substitute for checking bass with well-positioned speakers.

Joybuy products

Related products coming soon.

Frequently asked questions

Do I need a separate monitor controller if my audio interface already has a volume knob?

Not necessarily. A separate controller is most useful if your interface is out of reach or if you want to switch directly between sources, speakers or mono. First, check which features your interface already offers.

Will a monitor controller fix inaccurate bass when I switch between sitting and standing?

No. According to Genelec, the room, monitor placement and listening position can all affect the sound you hear. Check the speaker and listening positions at the height you work at; a different volume control won’t fix the problem by itself.

Can I connect a mono output directly to a subwoofer?

First check whether the output is filtered and where the crossover sits in the signal chain. According to the manufacturer, the mono output on the Palmer MONICON XL is full-range. PreSonus explains that a full-range mono output needs a crossover before the subwoofer, unless the subwoofer has one built in. This does not automatically confirm compatibility with a specific subwoofer.

Does the USB-C port on the PreSonus MicroStation BT work as a USB audio interface?

No. According to PreSonus, that connection is for power only. Connect your audio source to a suitable audio input.

What can I do in the Netherlands if my monitor controller develops a fault?

For a consumer purchase, the seller must offer a solution if the product is faulty. According to the Government of the Netherlands, there is no fixed statutory warranty period in the Netherlands; what you can reasonably expect from a product depends, among other things, on the product and normal use. Any manufacturer’s warranty is in addition to this.