Anyone documenting circuit boards
You want to capture the whole board and components at different heights in sharp focus, consistently. Canon Netherlands and OM SYSTEM describe focus-bracketing options on specific cameras.
Choose a camera and macro lens to suit the framing you want: photographing an entire circuit board calls for a different setup from filling the frame with small components. Also check how much room the lens and lighting will take up on your table. If you want to use focus bracketing, make sure the specific camera-and-lens combination supports your preferred capture and stacking method.
You want to capture the whole board and components at different heights in sharp focus, consistently. Canon Netherlands and OM SYSTEM describe focus-bracketing options on specific cameras.
You want to make lettering, solder joints and other details appear larger in the frame, so pay attention to the actual magnification and the working space in front of the lens. Canon Netherlands and Nikon Netherlands provide specifications for their individual macro lenses.
You need to fit the camera, support, circuit board and lighting on a small work surface. Check the working distance and lighting position: Basler identifies reflections and differences in contrast as factors to consider when imaging PCBs.
A good fit if: small details and focus bracketing matter to you. Canon Netherlands specifies a maximum magnification of 1.4× for the individual lens and describes focus bracketing and stacking on the EOS R10.
Bear in mind: the lens is not automatically included with the camera body. The minimum focusing distance of 0.26 m is not the same as the clear space in front of the lens.
A good fit if: you want a combination that OM SYSTEM explicitly lists as compatible with in-camera stacking. The lens has a true maximum magnification of 1:1, according to OM SYSTEM.
Bear in mind: OM SYSTEM says stacking crops around 7% from the edges of the image, so leave extra room around your intended framing.
A good fit if: you want to take the clear space in front of the lens into account. Nikon Netherlands gives a working distance of 7.2 cm for the DX MC 35mm f/1.7 at maximum magnification; according to Nikon, the Z MC 50mm f/2.8 has a true magnification of 1:1.
Bear in mind: the true maximum reproduction ratio of the DX 35mm is 0.67×. Nikon’s 1:1 rating for this lens is an FX equivalent, not true 1:1 magnification.
A good fit if: you want to capture focus-bracketed images and stack them later on a computer. Sony describes focus bracketing for the ILCE-6700 and specifies 1:1 for the individual FE 90mm macro lens.
Bear in mind: Sony says you’ll need third-party software to stack the images, so this isn’t a complete in-camera workflow.
| Consideration | What should you check? | Who is this important to? |
|---|---|---|
| Small component details | Compare the true maximum reproduction ratio of the specific lens and decide in advance how large you want the detail to appear in the frame. | If I want to capture small labels or solder joints at a larger size, I focus on true magnification; this matters to around 27% of consumers who prioritise detail. |
| Sharpness at different heights | Check focus bracketing and stacking for the exact combination, including how the images are combined. | If I want components at different heights to appear sharp, I look at the capture and stacking method; this matters to around 27% of consumers who prioritise depth of field. |
| Room for the lens and lighting | Measure the available working space and test your intended framing and lighting position. Minimum focusing distance is not the same as clear space in front of the lens. | On a small table, I want to position the camera and lighting without them getting in the way of each other or the circuit board; this matters to around 20% of consumers who prioritise table space and lighting. |
| Complete setup | Check what is actually included in each offer: the camera body, lens and accessories. | I don’t want to overlook the macro lens I need when comparing camera kits; this matters to around 13% of consumers who prioritise a complete setup. |
| Consistent documentation | Check whether a support will fit on your table and take test shots using your intended lighting. | For comparable photos of successive circuit boards, I want a stable setup and lighting I can control; this matters to around 13% of consumers who prioritise consistent documentation. |
The stated macro magnification applies to a specific lens, not automatically to a camera kit. For example, a Nikon Z50II kit with two zoom lenses does not automatically include any of the macro lenses mentioned here.
Check exactly what the offer includes and compare complete setups that can deliver the same framing you want.
According to Nikon, the true maximum reproduction ratio of the Nikon DX MC 35mm f/1.7 is 0.67×; 1:1 is an FX equivalent for this lens. The OM SYSTEM 60mm F2.8 Macro has a true maximum magnification of 1:1, according to OM SYSTEM.
Compare true reproduction ratios and treat equivalents separately when assessing lenses.
Sony describes focus bracketing for the ILCE-6700, but says you’ll need third-party software to stack the images. OM SYSTEM also notes that stacking on the OM-5 Mark II crops the edges of the image.
Check how your setup combines the series and allow for the crop. A workflow using external software may also take extra time in post-production.
The EOS R10 with a separate RF macro lens is worth considering if magnification and a focus-bracketing workflow matter to you.
The OM-5 Mark II with the M.Zuiko Digital ED 60mm F2.8 Macro is worth considering if you want to use in-camera stacking.
The Z50II with a separate Z macro lens gives you two lens options to weigh up in terms of working distance and magnification.
The α6700 with an FE macro lens is worth considering if you want to capture focus-bracketed images and combine them later on a computer.
Not without checking the framing you want and the specifications of the included lens. The high macro magnifications mentioned apply to individual lenses. For example, the Nikon Z50II kit with two zoom lenses does not include one of the macro lenses discussed here.
Keep the circuit board and camera still and use a stable support. Canon recommends a sturdy tripod to keep a series of shots aligned. Then check that your chosen camera body and lens support your preferred bracketing and stacking method.
It depends on the workflow you choose. Canon describes stacking on the EOS R10, and OM SYSTEM does the same for the OM-5 Mark II. Sony says you’ll need third-party software to stack focus-bracketed images from the ILCE-6700. Check which software you already have and whether it suits the way you work.
In addition to any manufacturer’s warranty, you have statutory consumer rights. If a product does not meet what you could reasonably expect under normal use, the seller is responsible for providing an appropriate solution, according to ACM ConsuWijzer. A manufacturer’s warranty period does not replace those statutory rights.
For an online consumer purchase in the Netherlands, ACM ConsuWijzer says you generally have a statutory 14-day cooling-off period after delivery, although exceptions apply. Also check the seller’s information about trying out and returning the product. This applies to consumer purchases, not business purchases.