Who is this buying guide for?

Uploading photos from a room behind thick walls

You want to know whether a mesh point will help where you upload. It’s not just the coverage in that room that matters: the point also needs a usable connection to the rest of the network. The Consumers’ Association advises placing extenders where you want to improve the signal.

A home with network cables

You can connect mesh points on either side of the obstacles via Ethernet and want to find an installation that works for you. TP-Link describes Ethernet backhaul as a way for Deco units to exchange data over a cable.

No way to run Ethernet

You can’t run a network cable to the planned locations. In that case, it’s important to check whether powerline networking works in your home, or whether wireless points can still reach each other reliably from suitable midway locations.

What should you look for when choosing?

Mesh with Ethernet backhaul

Choose this if: you can connect the mesh points using a suitable network cable or wall socket.

Bear in mind: you’ll need a suitable cable route and connections. Also check the Wi-Fi where you upload.

Mesh via powerline

Consider this if: running Ethernet isn’t practical, but the sockets are connected to suitable electrical wiring.

Bear in mind: performance depends on your electrical wiring and whether the points you choose are compatible.

Wireless mesh

Consider this if: you can place the points where they still have a usable wireless connection to each other.

Bear in mind: adding a point where there’s barely any reception won’t automatically give it a good connection.

Check your internet connection first

Start here if: uploads are slow even when you’re close to the router.

Bear in mind: this won’t fix a Wi-Fi dead spot, but it will help you work out whether the issue is inside your home or with your internet connection.

What to consider What should you check? Who is this important to?
Coverage where you upload Measure Wi-Fi and upload speed at the intended location; don’t rely solely on a stated coverage area. If I upload from a room behind thick walls, I want to know whether I’ll actually get coverage there. Around 36% of shoppers with this buying question put coverage in that location first.
Connection between mesh points First check whether Ethernet is an option. If not, look into suitable powerline networking or a wireless location where the points have a strong enough connection to each other. I want the points to reach each other reliably, even if the room where I upload has coverage. Around 29% of shoppers in this group prioritise the connection between points.
Cause of slow uploads Compare measurements by the router and where you upload, using a wired connection too if possible, and check your package’s upload speed. If uploads are slow even close to the router, I want to know first whether my internet connection is the limitation. Around 21% of shoppers in this group want to identify the bottleneck before buying.
Router and installation Check the router or access point mode, and which cables, power supply and features come with the exact model. I want to connect the mesh system to my existing network without an unnecessarily complicated installation. Around 14% of shoppers in this group prioritise compatibility and installation requirements.

Common buying mistakes

  • Assuming the stated range or Wi-Fi speed guarantees your upload speed

    Your actual connection depends on factors such as walls, placement and the device you’re using. Your internet connection’s upload speed also affects how quickly you can send photos.

    Measure where you upload and by the router. Use stated speeds and coverage areas only as a guide when comparing options, before testing the connection at home.

    If a midway location doesn’t work, you may still need to run a cable or try a different position.

  • Assuming powerline compatibility from a shared brand or mesh name

    TP-Link states that the Deco PX50 does not form a shared powerline backhaul with the Deco PX10, P7 or P9.

    Check the full model numbers and test the connection through the sockets you plan to use before combining points.

  • Checking only the device’s power supply on a PoE model

    For PoE power on the Deco X50-PoE, TP-Link specifies 802.3at or 802.3bt; 802.3af is not supported. The included adapter is an alternative power option.

    Check which power supply and cabling are available where you plan to install it, and whether PoE is needed there.

    A suitable power supply or cabling may be needed for a PoE setup.

Brands to compare

TP-Link

TP-Link describes several Deco setups for different ways of connecting mesh points.

  • According to TP-Link, the Deco X50 supports optional Ethernet backhaul. The PX50 uses G.hn powerline between compatible PX50 points.
  • According to TP-Link, the X50-PoE can be powered using the included adapter or connected to a suitable PoE power supply.
  • The PX50 does not provide powerline backhaul with the PX10, P7 or P9. For PoE power on the X50-PoE, TP-Link specifies 802.3at or 802.3bt, not 802.3af.

ASUS

ASUS describes the ZenWiFi XD5 as a multi-point system that can use Ethernet backhaul if there are connections at the planned locations.

  • ASUS lists Ethernet backhaul as an option for the XD5.
  • According to ASUS, you’ll need a compatible device to benefit from Wi-Fi 6. The available 160 MHz bandwidth on 5 GHz may be restricted in some regions; neither point predicts the speed you’ll get in a particular home.

FRITZ!

The FRITZ!Repeater 3000 AX is worth considering as an addition to a compatible FRITZ! mesh setup, for example with a LAN connection to a FRITZ!Box.

  • FRITZ! lists two gigabit LAN ports for this specific repeater model.
  • A standalone repeater is not the same as a complete mesh system. The mesh features available depend on the setup you choose.

NETGEAR

NETGEAR describes Orbi as a wireless mesh option to consider when there are no cables and the planned points can still reach each other.

  • NETGEAR states that many Orbi systems have a dedicated 5GHz backhaul band.
  • NETGEAR describes a different backhaul approach for the RBE770 series. This product range information doesn’t tell you how a specific model will perform behind thick walls.

Mesh products on Joybuy

This selection of Joybuy products includes multi-point mesh systems, with models and versions to compare for a range of home setups. Check the connection options, compatibility and required CE marking for the exact model.

TP-Link Deco BE68, 2-pack

TP-Link Deco BE68, 2-pack

An option to consider if you’re looking for a mesh system with multiple points. Check that the exact connection options suit the link between the points.

The product name specifies Wi-Fi 7 and a 2-pack.

Joybuy
ASUS ZenWiFi BD4 dual-band, 2.4 GHz and 5 GHz

ASUS ZenWiFi BD4, dual-band

An option to compare if you’re looking for a ZenWiFi mesh system. Check that the version you choose works with your existing ASUS mesh equipment and setup.

The product name specifies Wi-Fi 7 and the 2.4 GHz and 5 GHz frequency bands.

Joybuy
TP-Link Deco M4, 3-pack

TP-Link Deco M4, 3-pack

An option to compare if you’re looking for several mesh points. Check which features and connections suit the way you want to link the points.

The product name specifies dual-band Wi-Fi 5 (802.11ac) and a 3-pack.

Joybuy
TP-Link Deco X50, 3-pack

TP-Link Deco X50, 3-pack

An option to compare if you want to connect the mesh points via Ethernet. TP-Link describes optional Ethernet backhaul for the Deco X50.

The product name specifies dual-band Wi-Fi 6 (802.11ax) and a 3-pack. Check the connections on the exact model.

Joybuy
Huawei eKit OptiX FG736 BE3600 dual-band Wi-Fi 7 mesh router

Huawei eKit OptiX FG736 BE3600

An option to compare if you’re looking for a mesh router. Check that the exact model suits your existing router and the setup you want.

The product name specifies dual-band Wi-Fi 7.

Joybuy

Frequently asked questions

Should I check my Wi-Fi or upload speed first?

Compare an upload speed test next to the router, using a wired connection too if possible, with one from the room behind the wall. If the connection is already limited by the router, check your package’s upload speed; mesh won’t increase it.

Which connection between mesh points works well through thick walls?

If you can run a suitable cable, Ethernet backhaul can bypass the wireless connection between the points. Without a cable, you could look into suitable powerline networking or place wireless points only where they can still reach each other reliably. Performance depends on your home and installation.

Will a Deco PX50 work with older Deco powerline points over the mains?

Not as a shared powerline backhaul with the Deco PX10, P7 or P9. TP-Link states that the PX50 doesn’t work with these models for this purpose. Also check whether the sockets you plan to use provide a suitable connection in your home.

Can a mesh system work alongside my existing broadband router?

It can if the system has a suitable access point mode. TP-Link describes both router and access point modes for Deco. Check which features are available in that mode on the exact model, and connect a second router correctly.

Do I always need a PoE switch for the Deco X50-PoE?

No. TP-Link lists the included DC adapter as an alternative power supply. If you want to power the point through the network cable, TP-Link specifies IEEE 802.3at or 802.3bt; IEEE 802.3af is not supported.