Who is this choice relevant to?

Creator with a wired workspace

You upload large portfolio files from a room behind thick walls and can run a network cable to a mesh point. The connection between the mesh points is then an important factor in your choice. TP-Link Netherlands describes Ethernet backhaul as a way to connect Deco units using a cable.

Creator without a cable route

You can’t run a network cable and want to weigh up powerline against a wireless mesh point positioned where the connection is usable. For the Deco PX50, TP-Link Netherlands describes a connection between points using G.hn powerline.

Creator unsure what’s causing upload delays

You don’t yet know whether the delay is occurring at your workspace or at your internet connection. So, first take a wired measurement at the modem and compare it with the result at your workspace. Consumentenbond recommends using a network cable for a speed test.

What should you look out for in mesh Wi-Fi for portfolio uploads?

Start by taking a wired measurement at the modem. Then choose between Ethernet backhaul, powerline and wireless mesh based on your cable route and the connection where you upload.

What to consider What should you check? Which consumers?
Stable connection between mesh points Check whether the exact model supports Ethernet backhaul and whether you’ll have enough ports left over. Measure the upload speed at your workspace. If I can run a network cable to my workspace, I want the mesh points to communicate with each other over a wired connection. Around 36% of consumers prioritise this.
Connection without a network cable Check whether powerline connects the points to each other and test the connection at the sockets you plan to use. Also check whether existing adapters use the same protocol. If I can’t run a network cable and walls interfere with the wireless connection, I want an alternative link between the points. Around 29% of consumers prioritise this.
Positioning wireless points Find a location where the additional point still has a usable connection to the network. Check how many points are included in the set and measure the speed where you upload. If I don’t want to run cables, I look for a suitable place to position wireless mesh points. Around 21% of consumers are mainly looking for this flexibility.
Cause of slow uploads Compare a wired measurement at the modem with one at your workspace, and with the upload speed your provider lists for your fixed broadband connection. If I don’t yet know what’s causing the delay, I first want to find out whether mesh can help. Around 14% of consumers want to know this first.

Common buying mistakes

  • Mistaking a claimed Wi-Fi or powerline speed for your upload speed

    The upload speed of your fixed internet connection and the connection between mesh points are two different things. A stated product speed isn’t a measurement of your upload speed at home.

    First take a wired measurement at the modem, then take another where you upload your portfolio.

  • Placing an additional wireless point just behind a wall that blocks the signal

    An additional mesh point also needs a usable connection to the network. A thick wall can interfere with that connection.

    Try positioning it somewhere in between. If the wireless connection isn’t usable there, compare Ethernet backhaul with powerline.

  • Overlooking the ports and power supply included with the set

    The connection to the modem, a wired link between points and other devices may all use ports. PoE is also a separate power option.

    Before buying, work out which devices and mesh points you’ll connect, and check the exact version of the set.

Brands to compare for this mesh setup

TP-Link

The Deco range includes models for wired backhaul and for linking points using powerline. Which features matter depends on the version you choose.

  • TP-Link lists two 2.5Gbps ports per point and PoE power for the Deco X50-PoE. For the Deco PX50, the manufacturer describes G.hn powerline between points.
  • These are model specifications and manufacturer information, not independent upload speed measurements. Also check that any adapters you add use the same powerline protocol.

ASUS

The ZenWiFi XT9 is a tri-band Wi-Fi 6 mesh option for anyone considering a fully wireless setup.

  • ASUS lists versions with either one or two points.
  • ASUS warns that 160 MHz on 5 GHz may not be available in some regions. Tri-band doesn’t guarantee a good connection through thick walls.

NETGEAR

The Orbi 770 series is a tri-band Wi-Fi 7 mesh option with the option of wired backhaul.

  • NETGEAR lists a 2.5Gbps wired backhaul option for the Orbi 770 series.
  • The claimed total wireless speed isn’t a measured portfolio upload, and on its own it doesn’t show that this setup is a better fit than a wired Wi-Fi 6 configuration.

devolo

Magic 2 WiFi 6 next combines Wi-Fi with a connection through your home’s electrical wiring, for situations where you can’t run a network cable.

  • devolo lists a Starter Kit with two adapters and a Multiroom Kit with three adapters.
  • Wi-Fi speeds listed by the manufacturer are maximums, not guaranteed upload speeds. Test the connection at the sockets you plan to use.

Joybuy products for mesh Wi-Fi and portfolio uploads

These Joybuy products are options to compare for multi-point mesh setups, including models that may support a wired connection between points and tri-band configurations. Check the specifications and connections of the exact version before you choose.

ASUS ZenWiFi BT8 2-pack, tri-band Wi-Fi 7, white

ASUS ZenWiFi BT8 (2-pack), tri-band Wi-Fi 7, white

An option for anyone looking for two mesh points and a tri-band setup; the product name specifies Wi-Fi 7.

The bands listed are 2.4, 5 and 6 GHz. Tri-band doesn’t guarantee a connection through thick walls, so check coverage in the locations you plan to use.

View at Joybuy
TP-Link AX1800 mesh Wi-Fi system, Wi-Fi 6, 2-pack

TP-Link AX1800 mesh Wi-Fi system (2-pack)

An option to consider if you’re looking for a mesh set that may support a wired connection between points; the product description mentions Ethernet backhaul.

The product name specifies Wi-Fi 6 and a set with two points. Before installation, check how the exact version connects to your modem and other devices.

View at Joybuy
TP-Link Deco X50 dual-band Wi-Fi 6, 3-pack

TP-Link Deco X50 (3-pack), dual-band Wi-Fi 6

This set of three points is an option for anyone looking to position several mesh points; TP-Link describes Ethernet backhaul for Deco units.

The product name specifies dual-band Wi-Fi 6 on 2.4 and 5 GHz. Check the number of ports in use and measure the upload speed at your workspace.

View at Joybuy
TP-Link Deco XE75 Pro tri-band Wi-Fi 6E, 3-pack

TP-Link Deco XE75 Pro (3-pack), tri-band Wi-Fi 6E

An option for anyone looking for a tri-band mesh set with three points; check that the connection you want between points is supported by the exact version.

The product name specifies Wi-Fi 6E and bands at 2.4, 5 and 6 GHz. This information doesn’t tell you what upload speed you’ll get at your workspace.

View at Joybuy
TP-Link Deco X50-PoE dual-band Wi-Fi 6, 3-pack

TP-Link Deco X50-PoE (3-pack), dual-band Wi-Fi 6

An option to compare if you’re looking for a Deco set that may support a wired connection between points; TP-Link describes Ethernet backhaul for Deco units.

The product name specifies PoE and two Ethernet ports. TP-Link lists two 2.5Gbps ports per point for the X50-PoE. PoE and port specifications don’t guarantee upload speeds in your home.

View at Joybuy

Frequently asked questions

Can a mesh set help me upload my portfolio to the internet faster?

Only if the connection inside your home is the limiting factor. Take wired measurements at the modem and your workspace, then compare the first result with the upload speed your provider lists for your fixed broadband connection.

How can I check whether Deco points are connected to each other via Ethernet?

Check in the Deco app whether Ethernet backhaul is active. TP-Link describes different connections for Deco setups in router and access point mode. Follow the instructions for your mode and exact model, as this guidance doesn’t automatically apply to other brands.

What should I measure after setting up mesh points?

Measure the upload speed where you work. Compare the result with the wired measurement at the modem. If you have a wired Deco setup, also check in the app that the satellite is actually using Ethernet backhaul.

Does my statutory guarantee end after a two-year manufacturer’s warranty?

No. According to ACM ConsuWijzer, the statutory guarantee applies alongside any manufacturer’s warranty. If a product is faulty, the seller is responsible for providing an appropriate solution; what you’re entitled to expect depends on the product and the circumstances.

Do I need a licence to use Wi-Fi at home in the Netherlands?

No. According to the Dutch Authority for Digital Infrastructure, you don’t need a licence to use Wi-Fi at home if you use the frequencies designated for it and comply with the conditions of use. Separately, radio equipment offered on the Dutch market must meet the applicable European requirements. The RDI gives 1 August 2025 as the start date for stricter cybersecurity requirements; this doesn’t show that a particular version meets those requirements. Check the documentation for the exact model.