Who is this solution for?

Working in the loft

You want coverage in the loft despite the distance, ceilings or walls. Pay particular attention to the connection between the loft node and the rest of the network. TP-Link Netherlands describes Ethernet backhaul as a wired option, while the Consumentenbond recommends keeping obstacles between wireless nodes to a minimum.

Using two workspaces

You switch between the loft and a study further away, and want a reliable connection in both places, for example for video calls. Check the connection in both locations; the Consumentenbond points out that the position of the Wi-Fi nodes and any obstacles between them matter.

Living in a home without network cabling

You can’t run Ethernet, so you need to weigh up whether you can position wireless nodes in suitable places or use powerline with your electrical installation. The Consumentenbond stresses the importance of positioning nodes with few obstacles between them; TP-Link describes G.hn powerline for Deco PX50 units.

What should you look for when choosing?

First, decide how the nodes will communicate with each other. Then choose the positioning, number of units and connection to your existing network with both workspaces in mind.

Mesh with Ethernet backhaul

A good fit if: you can use network cables between the nodes, for example if you already have network sockets or can run a cable.

Trade-off: cabling requires installation or an existing connection. A wired connection removes the wireless route between nodes, but doesn’t guarantee a particular Wi-Fi speed on your laptop.

Fully wireless mesh

A good fit if: you don’t want to run a cable and can position the nodes where they can still reach each other reliably.

Trade-off: putting a node somewhere with an already weak incoming signal won’t automatically fix that weak connection. The Consumentenbond recommends keeping obstacles between nodes to a minimum.

Mesh with powerline backhaul

A good fit if: running a cable isn’t practical, a wireless connection between the nodes is difficult and your electrical installation can connect compatible units.

Trade-off: the socket and electrical installation affect the connection. TP-Link describes powerline backhaul for two Deco PX50 units; it isn’t interchangeable with Deco PX10, P7 or P9.

What to consider What should you check? Who should consider this?
Coverage on both floors Map possible positions for the modem, mesh nodes and any intermediate nodes; check for Ethernet backhaul if you can use a cable. If I need coverage in both the loft and the distant room, I want to know whether the nodes can reach each other reliably there. Around 36% of consumers put coverage at the top of their buying priorities.
Reliable working in both spaces Compare measurements by the router with measurements in both workspaces; also check whether your chosen devices can connect to a node using a cable. For video calls and other work, I don’t want a connection that works well in one workspace but falls short in the other. Around 29% of consumers prioritise a reliable connection.
Connecting without new cabling Check whether the wireless nodes can reach each other in their intended positions; for powerline, check that the chosen units and sockets are suitable. If running a cable isn’t an option, I want to choose a solution that will work in my home. Around 21% of consumers prefer a connection that doesn’t require new network cabling.
Connectivity and running costs Check the router or access point mode, the number of units and ports you need, any additional services and the power consumption of the full system. If I’m keeping my existing network, I want to know in advance how the system will connect to it and what it will cost to run. Around 14% of consumers prioritise connectivity and running costs.

Avoiding common buying mistakes

  • Assuming the coverage area guarantees a signal in the loft

    Distance, walls and ceilings affect the signal. Adding another node won’t automatically help if its connection to the rest of the network is already weak.

    First, work out the route between the mesh nodes, then check the connection in both workspaces. The Consumentenbond recommends positioning wireless nodes with as few obstacles between them as possible.

  • Assuming all powerline mesh nodes work together

    TP-Link states that the Deco PX50’s powerline backhaul is not compatible with Deco PX10, P7 or P9, or with standalone powerline adapters.

    Check the full model numbers and make sure the units can communicate through the sockets you plan to use.

  • Failing to check conflicting port information

    The Joybuy listing checked for the Deco PX50 mentions both one and three Ethernet ports per unit. TP-Link Netherlands lists three gigabit ports.

    Before buying, check the exact model and port details against the manufacturer’s information and the product listing for the version on offer.

  • Upgrading to a faster broadband package before identifying your Wi-Fi problem

    A slow connection could be caused by your internet connection, but it could also be down to Wi-Fi or the router’s position. A more expensive package won’t automatically solve a local coverage problem.

    First, compare a wired measurement by the router with measurements in your workspaces; the Consumentenbond advises against immediately upgrading to a faster package.

Relevant brands

TP-Link

TP-Link offers mesh models with different ways for the nodes to connect. According to TP-Link Netherlands, the Deco X50 has Wi-Fi 6, Ethernet backhaul and three gigabit ports per unit; the Deco PX50 also adds G.hn powerline.

  • Some models let you choose a wired connection; the PX50 also offers G.hn powerline for suitable setups.
  • According to TP-Link, the PX50’s powerline backhaul is not compatible with Deco PX10, P7 or P9. Manufacturer information can’t tell you how well the connection will work in your home.

FRITZ!

FRITZ! describes the three-piece Mesh Set 1700 as suitable for use with an existing router or a FRITZ!Box.

  • The manufacturer lists a gigabit LAN connection on each repeater and automatic updates.
  • Check which set and connection are right for your network; these features don’t tell you how well a wireless backhaul will work through your floor.

ASUS

ASUS describes the ZenWiFi BD4 as a dual-band Wi-Fi 7 mesh system with the option of wired backhaul.

  • According to ASUS, the system has two 2.5G ports and supports wired backhaul.
  • Wi-Fi 7 or the stated radio speeds don’t guarantee coverage between rooms in your home. Also check the exact regional version.

NETGEAR

NETGEAR describes the Orbi RBK763S as a tri-band Wi-Fi 6 system comprising a router and two satellites, with a dedicated wireless connection between the router and satellites.

  • The manufacturer lists a dedicated band for the connection between the router and satellites.
  • Even this information from the manufacturer doesn’t prove that the signal will remain strong enough through the floors and walls in your home. According to NETGEAR, the Armor service is included for one year.

Products on Joybuy

These mesh systems are options for connecting multiple workspaces to one network. For each version, check the number of nodes, how you want them to connect and how the system will connect to your existing router.

TP-Link Deco BE68 mesh system, 2-pack

TP-Link Deco BE68 (2-pack)

An option to consider if you need two mesh nodes for your workspaces; check the product information to see whether the nodes can connect in the way you want.

Joybuy
TP-Link Deco M4 dual-band mesh system, 3-pack, Wi-Fi 5

TP-Link Deco M4 (3-pack), dual-band Wi-Fi 5

The three units are designed for a mesh setup with multiple nodes. The product name specifies dual-band Wi-Fi 5 (2.4 GHz/5 GHz); check that the connection between the units will work in your home.

Joybuy
TP-Link Deco X50 mesh system, 3-pack, Wi-Fi 6

TP-Link Deco X50 (3-pack), dual-band Wi-Fi 6

The three units are an option if you want to position mesh nodes in several places. The product name specifies dual-band Wi-Fi 6 (2.4 GHz/5 GHz); check that the backhaul you want will work with your installation.

Joybuy
Linksys Velop Pro 7 tri-band mesh system

Linksys Velop Pro 7, tri-band Wi-Fi 7

A mesh option to compare if you want to connect several rooms. The product name specifies tri-band Wi-Fi 7 (2.4 GHz/5 GHz/6 GHz); check how you want the nodes to connect and whether the setup is compatible.

Joybuy
TP-Link Deco XE75 Pro tri-band mesh system, 3-pack, Wi-Fi 6E

TP-Link Deco XE75 Pro (3-pack), tri-band Wi-Fi 6E

The three units are an option for a mesh setup covering several locations. The product name specifies tri-band Wi-Fi 6E (2.4 GHz/5 GHz/6 GHz); check that this version is compatible with your network and the connection you want between nodes.

Joybuy

Frequently asked questions

Can I simply put an extra mesh node in the room with poor Wi-Fi?

First, check how the node connects to the other mesh nodes. The Consumentenbond recommends keeping obstacles between wireless nodes to a minimum, so an intermediate position may be more suitable. If you have suitable cabling, you can use Ethernet backhaul.

Can I use a Deco PX50 with my existing powerline adapter?

Not as part of the same powerline backhaul. According to TP-Link, the PX50 works with other PX50 units for this purpose, but not with standalone powerline adapters or Deco PX10, P7 and P9. This doesn’t rule out other network configurations.

How can I check whether my Deco nodes are connected by cable after installation?

In the Deco app, check whether the satellite node is shown as using Ethernet backhaul. TP-Link provides different cabling instructions for router mode and access point mode.

What costs will I have after buying?

Multiple Wi-Fi nodes use electricity continuously. Compare the power consumption of the complete setup and check which additional services are included with each system. The actual cost depends on the system you choose and your energy tariff.

Do I need a permit or registration for home Wi-Fi in the Netherlands?

According to the Dutch Radiocommunications Agency (Rijksinspectie Digitale Infrastructuur), Wi-Fi on designated licence-exempt frequencies does not require notification or registration, provided the conditions of use are met. Equipment placed on the market in the Netherlands must meet the applicable European requirements and carry a CE mark.