Who is mesh Wi-Fi relevant to in a shared studio?

Studio with workspaces in different areas

You want Wi-Fi at worktables and in shared spaces. Whether you connect the points wirelessly or use ethernet backhaul will depend partly on whether you can run cables.

Team with heavy network traffic

Several people work online at the same time. So don’t just look at the advertised Wi-Fi speed: consider the connection between Wi-Fi points and the ethernet ports available too.

Guest studio manager

Visitors need internet access, while work devices may need to stay protected. Check how guest isolation is configured and whether the network setup supports it.

What should you consider when choosing?

Wireless mesh

A good fit when: running cables between the Wi-Fi points you need isn’t practical and you want to extend coverage.

Bear in mind: the points use wireless capacity to communicate with each other, so position them where that connection will remain reliable.

Mesh with ethernet backhaul

A good fit when: you can run cables to the Wi-Fi points and want to use a mesh setup.

Bear in mind: cabling takes time and effort to install. If wired Deco points are connected behind a switch, you may need extra configuration for guest networks.

Managed access points

A good fit when: separate guest and work networks, along with configurable access rules, are important.

Bear in mind: check what gateway, power supply and other network equipment you’ll need. Extra management also takes time.

What to consider What should you check? Who is this important for?
Coverage at workstations Map out worktables, walls and possible positions for Wi-Fi points; check the connection where people will be working. If I have worktables spread around the studio, I want to know whether there’s a connection in the areas that matter. Around 29% of consumers prioritise coverage at workstations.
Network traffic at the same time Check the ports on the exact model and whether wired devices can be connected; the combined Wi-Fi speed doesn’t guarantee that speed for a single device. When several team members are working at once, I look at the connection between points and the ports for wired devices. Around 29% of consumers give simultaneous network traffic top priority.
Separating visitors Check the guest and isolation settings in the selected operating mode. After installation, test whether visitors can access local work devices. If visitors use the internet while work devices need to stay protected, I want to be able to check the separation myself. Around 24% of consumers prioritise keeping visitors separate.
Installation and management Check what router, app or gateway you’ll need, and how the points will be connected and powered. Anyone looking for a setup that’s easy to configure and manage will want to know in advance what equipment and settings are required. Around 18% of consumers give installation and management top priority.

Common mistakes when buying mesh Wi-Fi

  • Assuming the combined Wi-Fi speed is the speed at each workstation

    Real-world throughput and coverage depend on factors including the building and network traffic. With wireless mesh, the connection between points also uses capacity.

    Compare the ports and backhaul options on the exact model, and check the connection at the workstations you plan to use.

  • Assuming a guest network automatically keeps work devices separate

    Guest isolation needs to be configured correctly. If wired Deco satellites are connected behind a managed switch, you may need to configure the switch too.

    After installation, use a visitor’s device to test whether local work devices are accessible.

  • Planning the installation around the Wi-Fi points alone

    Depending on the setup, you may also need cables, a switch, a power supply, a gateway and installation work.

    Map out the connections for each point and check what power supply and existing network equipment your chosen setup requires.

    A managed switch or the choice between router and access point mode can add time to the configuration.

Brands to consider for a shared studio

TP-Link

Deco mesh systems are worth considering if you want to manage your setup through a mobile app. The Deco X50-PoE also offers PoE power and a choice of mounting options.

  • TP-Link says the Deco X50 has three gigabit ports per point; the Deco X50-PoE is listed with two 2.5GbE ports.
  • For a shared studio, check guest isolation, operating mode and whether switch configuration is needed. Advertised coverage doesn’t guarantee a good connection at every workstation in your space.

ASUS

The ZenWiFi BD4 is a dual-band Wi-Fi 7 mesh option with router, access point and mesh point modes.

  • ASUS specifies two auto-sensing 2.5GbE WAN/LAN ports and operation on 2.4 and 5 GHz.
  • The specifications don’t list a 6GHz band. ASUS says actual throughput and coverage depend on the environment.

Ubiquiti

The UniFi U6 Mesh is an access point for a setup with manageable network features, wireless meshing and guest isolation.

  • Ubiquiti lists PoE power, guest network isolation and one gigabit uplink for this access point.
  • Network segmentation also requires the rest of the network to be configured appropriately. The U6 Mesh isn’t a complete modem-router system.

NETGEAR

The Dutch Orbi 770 product range may be worth considering if you’re looking at a larger mesh system with a wired backhaul option.

  • NETGEAR lists Wi-Fi 7 and a 2.5GbE backhaul option for the RBE773 three-pack.
  • These product specifications aren’t a measure of performance in a design studio. The space and the level of network isolation you need should also be considered separately.

Joybuy product picks for mesh in the studio

These Joybuy picks focus on Deco mesh for multiple workstations, with models that vary in the number of units, ports and power options.

TP-Link Deco M4 (3-pack), dual-band Wi-Fi 5

TP-Link Deco M4 (3-pack), dual-band Wi-Fi 5

A set of three mesh points may suit a studio where you want to extend Wi-Fi to several workstations.

The product information lists two ethernet ports per point and a guest network feature.

According to TP-Link, Deco is set up through the mobile app.

View at Joybuy
TP-Link Deco X50 (3-pack), dual-band Wi-Fi 6

TP-Link Deco X50 (3-pack), dual-band Wi-Fi 6

This mesh system may suit you if you want to use several Deco units and connect wired devices too.

The product information lists three gigabit ports per unit, optional ethernet backhaul and guest networks.

According to TP-Link, setup is done through the mobile app.

View at Joybuy
TP-Link Deco X50-PoE (2-pack), dual-band Wi-Fi 6

TP-Link Deco X50-PoE (2-pack), dual-band Wi-Fi 6

This model may suit you if you want to install two mesh points powered by PoE.

The product information lists two ethernet ports per unit and guest access.

Check what PoE equipment and other network hardware your setup will need.

View at Joybuy
TP-Link Deco XE75 (3-pack), tri-band Wi-Fi 6E

TP-Link Deco XE75 (3-pack), tri-band Wi-Fi 6E

A set of three mesh units may suit you if you want to extend Wi-Fi to several areas of the studio.

The product information lists tri-band Wi-Fi, three gigabit ports per unit and guest access.

Check the ports and settings on the exact model against your existing network.

View at Joybuy
TP-Link Deco X50-PoE (3-pack), dual-band Wi-Fi 6

TP-Link Deco X50-PoE (3-pack), dual-band Wi-Fi 6

This set may suit you if you want to install three mesh units powered by PoE.

The product information lists two ethernet ports per unit and guest access.

Check what PoE equipment and any switch configuration your installation will need.

View at Joybuy

Frequently asked questions about mesh Wi-Fi in a design studio

Do you need an internet connection as well as a mesh system?

Yes. Deco needs an existing internet source, such as a modem or an ethernet wall socket. TP-Link also recommends choosing router or access point mode to suit your existing network.

Does every mesh point need to be connected by cable?

No. TP-Link says wired and wireless connections between Deco points can be combined within one network. If you’re using cables, check the connection order required for your chosen operating mode.

Is a guest network automatically completely separate from studio workstations?

Don’t assume so: check the isolation settings in the operating mode you’re using and test whether visitors can access local work devices. If wired Deco satellites are connected behind a managed switch, you may need to configure the switch as well.

Might you need installation equipment in addition to the mesh points?

Yes. Depending on your setup, you may need network cables, a suitable switch, PoE power or installation work. Also check what equipment and management method the exact model requires.

Can a studio in the Netherlands use Wi-Fi without a licence?

According to the Dutch Authority for Digital Infrastructure, Wi-Fi can be used without a licence in business premises when designated frequencies are used and the conditions of use are met. Radio equipment placed on the market in the Netherlands must also meet the applicable European requirements, including the required CE marking. Stricter digital security requirements have applied since 1 August 2025.