Studio staff working at the far end of the room
You want usable Wi-Fi coverage at workstations beyond the corridor. The Consumers’ Association lists walls and other obstacles as factors that can interfere with a Wi-Fi signal.
Start by checking the connection at your workstations and at potential Wi-Fi access point locations: an extra point only helps if it has a usable network connection of its own. If you can run cables to suitable locations, compare mesh with Ethernet backhaul against a wired access point. If you can’t run cables, test the wireless connection between the points on site. TP-Link and ASUS document Ethernet backhaul for the systems mentioned, while guest access and features used behind an existing modem router depend on the specific model and configuration.
You want usable Wi-Fi coverage at workstations beyond the corridor. The Consumers’ Association lists walls and other obstacles as factors that can interfere with a Wi-Fi signal.
Your choice depends on the connection between the Wi-Fi points. TP-Link and ASUS document Ethernet backhaul for compatible Deco and ZenWiFi models. If you don’t have cabling, it’s important to test the wireless connection at the intended locations.
You want to give visitors access without automatically giving them the same network access as your studio devices. Ubiquiti describes network isolation as a configuration option, so check which settings your chosen system offers and how to configure them.
Choose this when: you can run cables to suitable locations on either side of the corridor and want to manage your Wi-Fi network centrally.
Consider: the points need suitable cables and ports, and must be connected correctly to the main unit or router.
Choose this when: running cables isn’t practical and you can find a location where the mesh point itself still has a good connection.
Consider: walls, obstacles and additional wireless hops can limit the connection. Test both the point’s location and the workstation.
Choose this when: reception is poor mainly in a remote work area, there’s already a network socket there and you want to keep your existing router.
Consider: check how the network name, roaming and guest access are managed. An extra point won’t fix a problem with the internet connection itself.
First, check your internet connection, then test the intended locations. This helps you distinguish coverage at the workstation from the connection the Wi-Fi point itself needs to the rest of the network.
| Buying concern | What should you look for? | Who is this most important to? |
|---|---|---|
| Coverage at workstations beyond the corridor | Check the fixed workstations and test potential point locations before deciding how many points you need. | I want to work at fixed workstations beyond the corridor and test coverage there specifically. Around 36% of consumers prioritise coverage at those workstations. |
| Connection between mesh points | Check the available cable routes and ports. For wireless placement, test the connection at every intended point location. | If I can run cables, I want to know whether Ethernet backhaul will work for me; without cabling, I want to check the wireless route first. Around 29% of consumers say the connection between points is their main buying concern. |
| Managing shared and guest access | Check which guest, client and network isolation options are available in your chosen configuration. | I want to give visitors Wi-Fi access while checking how access to studio devices is managed. For around 21% of consumers, managing guests and regular users comes first. |
| Compatibility with existing equipment | Check the router or access point mode and what components or power supply you’ll need. Test the internet connection over a wired connection first. | I may want to keep my existing router and know in advance what installation components I’ll need. Around 14% of consumers say existing equipment and installation are their main buying concern. |
Walls and other obstacles can interfere with the signal. So a stated coverage area doesn’t automatically tell you whether a specific workstation will have a connection.
Test the intended point locations as well as the workstations in the studio.
The point also needs a usable connection to the network. A strong signal between a laptop and the nearest point doesn’t tell you enough about the connection between that point and the rest of the network.
Check the connection between the points and, where possible and supported, use a network cable for Ethernet backhaul.
PoE requirements vary by model. And having a guest network doesn’t automatically mean devices are properly isolated from other networks.
Check the exact model, the power supply required and the guest access and isolation settings available. For the Deco X50-PoE, TP-Link specifies a compatible power supply or switch compliant with IEEE 802.3at or IEEE 802.3bt.
A suitable switch or power supply may need to be purchased separately for a PoE model.
Worth considering if you’re comparing Deco models with Ethernet backhaul or a separate PoE model.
The ZenWiFi XD5 is worth comparing if Ethernet backhaul and configurable Wi-Fi network names matter to you.
Worth considering if you’re comparing wireless and wired connections between mesh points.
Worth considering if you’re looking at separate access points and settings for studio and guest networks.
These mesh systems let you compare coverage, connections between points and placement in a shared design studio. For the specific model on offer, also check the CE marking required by the Dutch Authority for Digital Infrastructure.
Image unavailable
A two-unit mesh set for comparing wired and wireless connections between points.
Wi-Fi 7. The product description lists 10, 2.5 and 1 Gbps ports per unit.
Image unavailable
A three-unit set for comparing several possible locations in the studio.
Wi-Fi 6, dual-band (2.4 GHz/5 GHz) and three Gigabit Ethernet ports per unit. The product description lists optional Ethernet backhaul.
Image unavailable
An option to compare if you want several units to work together under one Wi-Fi network name.
The product description lists Wi-Fi 7, dual-band operation and management through the HUAWEI SmartLife app.
Image unavailable
A two-unit set to compare if power over a network cable and guest access matter to you.
Wi-Fi 6 and two Ethernet ports per unit. For PoE, TP-Link specifies IEEE 802.3at or IEEE 802.3bt; a compatible power supply or switch is required.
Image unavailable
A three-unit set for comparing several point locations and guest access.
Tri-band Wi-Fi 6E (2.4 GHz/5 GHz/6 GHz) and three Ethernet ports per unit.
No. First, test your internet connection with a wired computer and see whether moving your router or adding a single wired access point could solve the local coverage problem.
Put it in a practical location where the point itself still has a good connection to the network. Then test the workstation you want to reach too; a strong connection between your laptop and a nearby point isn’t enough on its own.
For the exact model, check the router or access point mode, the cable layout and which equipment manages network and guest features. TP-Link provides different connection instructions for Deco depending on the operating mode.
Check how many points and cables you’ll need, and whether a PoE model requires a separate compatible power supply or switch. The Dutch government distinguishes between the manufacturer’s warranty and statutory rights. Its guidance applies to consumer purchases and may not apply in the same way to a business purchase for a studio.
The Dutch Authority for Digital Infrastructure says Wi-Fi can be used without a licence, including for business purposes, provided the relevant conditions are met. This doesn’t guarantee interference-free use. Also check that the specific equipment on offer meets the applicable European requirements and carries the required CE marking.