Who is this choice relevant to?

Circuit board documenter

You want to photograph a whole circuit board, or a larger section of it, clearly and consistently. Angle of view and a stable setup matter more to you than maximum magnification. Canon Europe recommends using a tripod or other support for still-life photography.

Soldering detail enthusiast

You want to capture tiny joints or markings so they fill the frame, so you’re comparing 1:1 magnification with higher magnification. Specifications from Canon Europe, Sony Netherlands and Laowa show examples of different maximum magnifications.

Tabletop photographer with limited space for lighting

You need to fit the camera and lighting around the circuit board. The clear space in front of the lens is therefore a separate consideration from magnification; Sigma Corporation and Sony Netherlands publish model-specific figures for this.

What should you look for when buying?

First decide what framing you need, then check the mount and sensor size, and finally make sure your complete camera setup will fit on your table.

What to consider What should you check? Who should prioritise this?
Room for lighting Compare the working distance at your desired magnification. Sony Netherlands lists a working distance of almost 8 cm for the FE 50mm; the minimum focusing distance is 16 cm and is measured from a different point. If you need to position lights beside the lens and have little table space, the clearance in front of the lens is important. Around 33% of consumers in this situation put space and lighting first.
Framing and detail Decide on the smallest area you need to frame and compare the maximum magnification of the exact model. Canon Europe specifies a maximum of 0.5× for the RF 35mm; Sony Netherlands lists 1:1 for the FE 50mm, while Laowa specifies a maximum of 2:1 for the 65mm. If you want tiny solder joints or component markings to fill the frame, magnification matters more than a wide overview. Around 27% of consumers give detail magnification top priority.
Mount and sensor size Check the exact mount on your camera body and whether the lens is compatible with your sensor size. Sony Netherlands specifies the FE 50mm for Sony E and full-frame; Nikon Netherlands specifies the Z MC 50mm for Nikon Z and FX. If you want to use the lens with your current camera, check the exact version first, before comparing magnification. Around 20% of consumers put camera compatibility first.
Sharpness at different heights Consider whether you can keep your setup stable and whether your workflow allows for multiple focus shots. Nikon Netherlands describes combining images taken with different focus points to increase depth of field. When components at different heights need to be in focus, a series of focus shots may matter more than extra magnification. Around 20% of consumers put sharpness across components at different heights first.

Common buying mistakes

  • Assuming ‘macro’ means 1:1

    Maximum magnification varies from lens to lens. Canon Europe specifies a maximum of 0.5× for the RF 35mm F1.8 MACRO IS STM, while other models offer 1:1 or more.

    Compare the maximum reproduction ratio of the exact model with the area you want to photograph.

  • Confusing minimum focusing distance with working distance

    Minimum focusing distance and the clear space in front of the lens are measured from different points. Sony Netherlands lists a working distance of almost 8 cm and a minimum focusing distance of 16 cm for the FE 50mm.

    Check the working distance at the magnification you plan to use, and map out your complete camera and lighting setup on the table.

  • Ordering the wrong mount version

    A lens may be available with different mounts, so magnification alone won’t tell you whether it will fit your camera.

    Compare the full lens version with the exact mount and sensor size of your camera body.

Brands to consider

Canon

Canon Europe specifies a maximum magnification of 0.5× for the RF 35mm F1.8 MACRO IS STM and 1.4× for the RF 100mm F2.8L Macro IS USM.

  • The models listed offer different maximum magnifications for Canon RF cameras.
  • The RF 35mm is not a 1:1 lens. The stated minimum focusing distance of the RF 100mm is not the clear working distance in front of the lens.

Sony

Sony Netherlands specifies the FE 50mm F2.8 Macro for Sony E-mount and full-frame cameras, with 1:1 magnification.

  • Sony lists a working distance of almost 8 cm for this model.
  • That working distance is not the same as the 16 cm minimum focusing distance; allow room for lighting.

Nikon

Nikon Netherlands specifies the Z MC 50mm f/2.8 for Nikon Z and FX, with 1:1 magnification.

  • Nikon also describes the lens as suitable for everyday photography.
  • Don’t infer the working distance from the focal length alone; check how the setup will fit on your table.

Sigma

Sigma Corporation specifies 1:1 magnification and a 141 mm working distance at that magnification for the 105mm F2.8 DG DN MACRO | Art.

  • Sigma lists versions with Sony E and L mounts.
  • The stated working distance applies to this model. Check that the longer camera setup will fit on your table.

Laowa

According to Venus Optics, the Laowa 65mm f/2.8 2x Ultra Macro APO offers a maximum magnification of 2:1 and is designed for APS-C cameras.

  • The higher maximum magnification may be useful when 1:1 isn’t enough to capture small details.
  • The stated minimum focusing distance of 17 cm is not the clear space in front of the lens. Check the mount and allow room for lighting.

Joybuy products

Related products will be available soon.

Frequently asked questions

Do you need 1:1 magnification to photograph a complete circuit board?

Not necessarily: 1:1 produces a life-size image on the sensor, but the framing you need depends on the circuit board and sensor size. Choose magnification based on what you want to show in one shot; a lens with 0.5× magnification may work well for a wider view.

How can you stop taller components from appearing out of focus?

Keep the camera steady when photographing a stationary circuit board. If a single plane of focus isn’t enough, you can take shots using different focus points and combine them; Nikon Netherlands describes this technique as focus stacking. Check that the features and software in your setup support it.

What does the minimum focusing distance in the specifications mean?

The minimum focusing distance is measured from the camera sensor, not from the front of the lens. For the FE 50mm, Sony Netherlands distinguishes between a minimum focusing distance of 16 cm and a working distance of almost 8 cm; when planning your table layout, check the working distance at the magnification you intend to use.

What consumer rights apply when buying online in the Netherlands?

When you buy from a business online or at a distance, you generally have 14 days to change your mind, with some exceptions, according to the Dutch government. You’re also entitled to a product that works properly. If there’s a problem, contact the seller for a solution, even if the product comes with a manufacturer’s warranty.