A light that only switches on when needed can be useful in a hallway, bedroom, cupboard, bathroom, garden or driveway. However, not every LED motion sensor light is suitable for every situation. A sensor may respond too late, an outdoor light may not be sufficiently protected from rain, or a battery may run flat sooner than expected.
So don’t just look at the number of LEDs or a high light output. Pay particular attention to the sensor, power supply, protection rating and how you plan to install the light.
A product with lots of LEDs may give off bright light, but that doesn’t automatically mean the light is distributed evenly. Check the luminous flux in lumens, the beam angle and where you plan to install the light. A modest light output is often enough for a cupboard or bedside table. A wider spread is more practical for a driveway or patio.
An indoor motion sensor light usually responds to movement within a certain range, and only when the ambient light is low enough. Product specifications may state a range of 3 to 5 metres and a threshold of up to 20 lux. Don’t place the light behind an obstacle, and point the sensor towards the area where you walk.
Outdoor motion sensor lights are also affected by rain, temperature, wind and direct sunlight. If a sensor light is mounted at the wrong angle, it may switch on too early or too late.
A rechargeable sensor light needs to be charged regularly via USB. A solar outdoor light with a sensor needs enough direct sunlight during the day to recharge its built-in battery. In a shady garden or during dark winter days, its operating time may be shorter than on sunny days.
Check:
For a bedroom or nursery, an LED night light with a motion sensor and several brightness levels is a good choice. A compact range is enough for a cupboard. A wide detection angle is more useful around a garage or driveway.
There are three common options:
A wireless LED light is handy if you don’t want to drill holes or conceal cables. If you’re mounting it with tape, check that the surface is clean, dry and flat. A screw fixing is often more suitable for a heavier wall light.
The IP rating indicates how well a product is protected against solid particles and moisture. IP44 provides protection against splashing water, among other things. This is suitable for many sheltered outdoor locations, but not for immersion or direct jets of water. According to the product specifications, a product with IP65 is better protected against dust and jets of water.
Check the mounting position too. Even a light with a higher IP rating won’t be much use somewhere water is constantly collecting on the charging point or sensor.
A dimmable LED light gives you more control over how you use it:
A lower brightness is often more comfortable for finding your way around at night. Brighter light may be more practical in a kitchen or pantry. Bear in mind that “dimmable” can mean five fixed levels rather than stepless dimming.
Why it suits this profile: This set is designed for small spaces such as a bedroom, nursery or hallway. The built-in battery charges via USB, and the light has five brightness levels.
The specifications state a sensor range of 3–5 metres and operation at up to 20 lux. This helps you work out in advance where the light will be suitable.
500mAh battery, USB charging, three colour temperatures and a stated operating time of up to 10 hours in sensor mode.
Why it suits this profile: This solar wall light is designed for permanent installation by an entrance, patio or garden path where there’s no power cable.
The product specifications list IP44, two light modes and an integrated dusk and motion sensor. It still needs to be placed somewhere with enough direct sunlight.
1000 lumens, 3000K warm white light, integrated LED and no mains connection required.
Why it suits this profile: This motion-sensor cabinet light is 10 mm thick, so it fits inside cupboards, on shelves or underneath kitchen cabinets.
The dimensions, 3–5 metre PIR range and USB charging function are clearly stated. That means you don’t have to rely on general terms such as “smart” or “wireless”.
61 LEDs, 1100mAh battery, three colour temperatures and two lights per set. According to the product information, installation doesn’t require drilling.
Why it suits this profile: The three adjustable heads are designed to provide wider coverage for areas such as a driveway, garage, garden or patio.
The product specifications list IP65, a 180-degree detection angle and a range of up to 60 feet. Check in advance that the stated distances suit your chosen mounting position.
302 LEDs, a stated luminous flux of 3000 lumens, three light modes and a 1800mAh solar-powered battery.
We’ve put together a complete, up-to-date list of products that meet these strict selection criteria and the applicable European safety regulations.
Place the light where the sensor has a clear view of the route you walk along. Avoid branches, doors or furniture that could block its range. Test the light at different heights and angles before securing it in its final position.
Operating time depends on the type of light, how often it switches on, the battery and the surroundings. With a rechargeable light, you’ll need to charge it periodically. For solar lighting, cloud cover, shade and dirt on the panel affect the available energy. Also check the warranty and information about the integrated LED module.
It can, because the light isn’t on all the time. Actual energy use depends on the wattage, how long it stays on each time and how often it is activated. So compare the wattage and operating mode rather than relying solely on the term “energy-efficient”.