Who are these setups for?

Digitising cassette tapes

You want to listen to the left and right channels during transfer, and distinguish issues in the recording chain from anything added by the speakers or room. The International Association of Sound and Audiovisual Archives points out that a misaligned playback head can affect high frequencies and phase relationships; monitors can’t fix this afterwards.

Listening at a sit-stand desk

Your listening height changes, and space beside your screen is limited. Genelec recommends equal distances, a symmetrical setup and speakers aimed at your listening position. Bear this in mind when setting up for both sitting and standing.

Connecting your existing audio equipment

You already have a cassette deck or audio interface and want to know whether its outputs will work with a compact stereo system or two separate active monitors. Also check whether the package contains one speaker or a pair.

What should you consider when choosing?

Start by checking the connections on your existing equipment and whether you have room for two speakers. Then make sure you can keep them aimed at your changing listening height, and check whether the product is sold as a complete stereo pair.

What to consider What should you check? Who is this important for?
Stereo image and transfer Check that you’re getting a stereo pair and can position both speakers at equal distances from your listening position. If I want to assess the left and right channels of a cassette transfer, I need to be able to position the speakers evenly. Around 33% of consumers put checking the transfer first.
Listening height and positioning Measure the space on either side of your screen and see whether you can aim the speakers at your listening position when sitting and standing. When I use my desk sitting down and standing up, I want to be able to aim the speakers at my listening position. Around 27% of consumers say changing listening height is their main concern.
Connections Make a note of the outputs on your deck or interface, then check the connector type and cables required for each channel. If my deck or interface is already in use, I want to know whether its wired outputs will work with the monitors. Around 20% of consumers prioritise compatibility.
Complete stereo pair Check what’s included in the product and which cables you’ll need to connect both channels. I want to avoid ordering just one speaker when I need stereo. Around 20% of consumers are mainly looking for a complete stereo setup.

Common buying mistakes

  • Mistaking a single monitor for a stereo set

    The Genelec 8010A is sold individually, while the PreSonus Eris 3.5 2nd Gen is listed as a pair. One monitor on its own doesn’t give you a stereo pair for checking the left and right channels.

    Before buying, check how many speakers are included and compare the cost of the complete stereo setup.

  • Not checking your existing connections

    The original IK Multimedia iLoud Micro Monitor has RCA and 3.5mm inputs; the Genelec 8010A has an XLR input on each speaker. A monitor’s input won’t necessarily match the outputs on your deck or interface.

    Make a note of the left and right outputs, then check which connectors and cables you’ll need.

  • Comparing frequency limits directly

    Genelec specifies 67 Hz at -6 dB for the 8010A, while IK Multimedia specifies 45 Hz at -10 dB for the original iLoud Micro Monitor. As these figures use different measurement limits, they don’t, by themselves, prove which monitor is better suited to checking cassette transfers.

    Only compare frequency specifications when they’re based on the same measurement method, and take the positioning in your room into account too.

Relevant brands to consider

PreSonus

The Eris 3.5 2nd Gen is a compact active stereo system for a desk where a choice of wired inputs is useful.

  • PreSonus says this model has RCA, 3.5mm and balanced TRS inputs, a headphone output on the front and tone controls.
  • The specified frequency response starts at 80 Hz; this doesn’t prove that every issue in the low-frequency range will be audible. This is the version without Bluetooth.

IK Multimedia

The original iLoud Micro Monitor is a compact pair of speakers with analogue RCA and 3.5mm inputs.

  • IK Multimedia lists a desktop setting and an included speaker connection cable.
  • According to the manufacturer, Bluetooth has higher system latency than the analogue input under the specified test conditions. For checking picture and sound at the same time, a wired connection is preferable. Check your own setup too.

Genelec

The compact 8010A is a single active monitor for a setup with two separate speakers and compatible XLR outputs.

  • Genelec lists room compensation switches and an XLR input on each monitor.
  • The package contains one monitor, and the model doesn’t have an RCA input. You’ll therefore need two units for stereo, as well as compatible connections.

Yamaha

The HS5 is a single active nearfield monitor with a 5-inch woofer; make sure you have room for two separate cabinets.

  • Yamaha specifies XLR and TRS inputs, as well as ROOM CONTROL and HIGH TRIM controls.
  • The available Yamaha documentation gives different lower limits at -10 dB. Don’t use these figures as a precise basis for comparing bass response with another model.

JBL Professional

The 305P MkII is a single active nearfield monitor with connections for a two-speaker setup.

  • JBL lists balanced XLR and 6.35mm TRS inputs, along with Boundary EQ settings.
  • These adjustment options are product specifications, not proof of how the monitors will perform at your desk or in your room.

Joybuy products

Related products coming soon.

Frequently asked questions

How should I set up monitors if I switch between sitting and standing?

Position the left and right monitors at equal distances and aim them both at your listening position. Genelec describes an equilateral triangle as the ideal stereo setup; check their direction again whenever you change the desk height.

Can a better studio monitor fix a cassette that was transferred incorrectly?

No, a monitor can’t restore information that was lost during playback. The International Association of Sound and Audiovisual Archives says that a misaligned playback head can affect high frequencies and phase relationships, while digital correction can’t recover lost high-frequency information. So check the playback chain too.

Can I use frequency limits to compare two models?

Only if the figures are given using the same measurement method. Genelec, for example, specifies 67 Hz at -6 dB for the 8010A, while IK Multimedia gives 45 Hz at -10 dB for the original iLoud Micro Monitor. These figures aren’t directly comparable.

Am I always limited to a two-year warranty in the Netherlands?

No. According to the Dutch government, there’s no fixed statutory warranty period in the Netherlands. You’re entitled to a product that meets what you can reasonably expect of it, and should contact the seller if there’s a problem. A manufacturer’s warranty is additional; the right solution depends on the fault and the circumstances.