Who is this guide for?

Photo uploader with weak basement Wi-Fi

Your internet works well elsewhere, but the Wi-Fi struggles when you upload from the basement. You mainly need a better connection in that room, not necessarily a faster main router.

Photo uploader who can run a cable

There’s already an Ethernet cable running to the basement, or you can install one. You want to use Wi-Fi down there and may want to keep your existing router.

Photo uploader with no way to run a cable

Running an Ethernet cable to the basement isn’t an option, so you’re comparing a wireless mesh point with a connection through your home’s electrical wiring.

What should you consider when choosing?

Start by checking the wired upload speed next to your router, then test Wi-Fi where you send the photo album from. This will help you work out whether the issue is mainly your internet connection or the link to the basement.

What to consider What should you check? Who is this important for?
Coverage where you upload Check the Wi-Fi upload speed in the basement and see whether a suitable midway spot has a usable signal for an extra access point. If I upload photos in the basement, I want a usable Wi-Fi connection there without immediately replacing my main router. Around 36% of consumers prioritise basement coverage above all else.
Why the upload is slow Compare repeated tests using an Ethernet cable next to the router with tests over Wi-Fi in the basement. If I don’t know why an upload is slow, I want to check my internet connection separately from Wi-Fi first. Around 29% of consumers prioritise identifying the upload bottleneck.
Connection between floors Check whether you can run a cable, whether a wireless midway point gets a strong enough signal, or whether powerline works through the sockets you plan to use. If I can’t run a cable to the basement, I want to know which connection between floors will work there. Around 21% of consumers prioritise whether the connection is feasible.
Set-up and use Check how many access points you need, which connections are required, the operating mode and whether the necessary CE marking is present. If I add extra equipment, I want to know what I’ll need and which features will remain available. Around 14% of consumers prioritise the set-up, required equipment and safe use.

Common pitfalls

  • Assuming faster Wi-Fi means faster photo uploads

    Changing your home Wi-Fi alone won’t make a slow wired internet connection any faster.

    First, compare the upload speed using an Ethernet cable next to your router, then test Wi-Fi where you send the photos from. The Consumers’ Association recommends connecting your computer to your home network with an Ethernet cable when running a speed test.

    This could save you from buying a router or changing your broadband package unnecessarily.

  • Placing a wireless mesh point where the signal is already weak

    An extra access point also needs a usable connection to the rest of your network. A weak wireless link between floors can limit the connection to the basement.

    Try a midway spot where the access point still gets a good signal, or see whether you can run an Ethernet cable to it.

    A less suitable location could mean you still need to find another spot or run a cable.

  • Assuming powerline adapters or mesh models are interchangeable

    Compatibility varies between product families. For example, TP-Link says the Deco PX50 doesn’t provide powerline backhaul with the PX10, P7 or P9; devolo says Magic and older dLAN adapters don’t work together.

    Before expanding your set-up, check the full model names and make sure the existing and new devices can work together to provide the connection you need.

  • Expecting access point mode to retain every router feature

    TP-Link says some Deco features, including parental controls and port forwarding, aren’t available in access point mode.

    Decide which features you need and check the operating modes available on the exact product you’re considering.

Brands to compare

TP-Link

TP-Link describes the Deco X50 as a mesh system with optional Ethernet backhaul, and the Deco PX50 as a mesh system with G.hn powerline. These offer different ways to connect to a basement.

  • The Dutch product specifications list Wi-Fi 6 and gigabit ports for both product lines.
  • These specifications don’t tell you what upload speed you’ll get in a particular basement. According to TP-Link, the PX50 powerline backhaul doesn’t work with the PX10, P7 or P9.

ASUS

The ASUS RT-AX58U is a standalone Wi-Fi 6 router with router, access point and AiMesh node modes, among others.

  • ASUS lists four gigabit LAN ports for this model.
  • The exact hardware version matters: ASUS lists different processor versions for V1 and V2. A standalone router won’t, on its own, guarantee coverage in the basement.

FRITZ!

FRITZ! explains how a FRITZ!Repeater can be connected via LAN and added as an extra Wi-Fi point to an existing FRITZ!Box mesh network.

  • This set-up lets you connect a repeater using an Ethernet cable.
  • The Wi-Fi settings transfer described applies to the specified FRITZ!Box mesh set-up. It doesn’t prove that the same integration will work with every router.

devolo

Devolo describes Magic powerline adapters that can carry network data through your home’s electrical wiring to a Wi-Fi point.

  • The Magic 2 WiFi 6 next Starter Kit is described as a set with two adapters and two gigabit LAN ports on the Wi-Fi adapter.
  • Performance and upload speed depend on the connection through your existing electrical wiring. Devolo says Magic and older dLAN adapters aren’t compatible with each other.

NETGEAR

NETGEAR describes Ethernet backhaul between the router and satellites for supported Orbi systems.

  • A wired connection between access points is worth considering if a wireless connection between floors is difficult.
  • The support mentioned applies to the Orbi systems described. Check the connections available on the specific set you’re considering.

Joybuy products for this situation

Below are mesh products, a powerline Wi-Fi kit and a router to compare for home Wi-Fi and network connectivity. For each model, check that the connections, operating mode and compatibility suit your route to the basement.

TP-Link Deco E4 mesh system, 3-pack

TP-Link Deco E4, 3-pack, dual-band Wi-Fi 5

A mesh system with several access points could suit you if you want Wi-Fi in more than one area of your home. Test whether the connection to the basement is usable.

The product name specifies dual-band Wi-Fi on 2.4 GHz and 5 GHz, and Wi-Fi 5 (802.11ac).

View at Joybuy
TP-LINK TL-WPA7517 KIT powerline adapter starter kit

TP-LINK TL-WPA7517 KIT powerline adapter starter kit

If you can’t run an Ethernet cable to the basement, this powerline Wi-Fi kit could be an option, provided it works over your existing electrical wiring.

Test the connection using the sockets you plan to use for your set-up.

View at Joybuy
Huawei eKit OptiX FG736 BE3600 dual-band Wi-Fi 7 mesh router

Huawei eKit OptiX FG736 BE3600 dual-band Wi-Fi 7 mesh router

The product description says that linked units can form a mesh network with one SSID. Check whether this set-up suits the route to your basement.

The product name specifies dual-band Wi-Fi 7.

View at Joybuy
ASUS RT-AX52 Pro AX3000 dual-band wireless router

ASUS RT-AX52 Pro AX3000 dual-band router

This router could suit you if you need a main router or already have compatible ASUS equipment for AiMesh expansion.

The product name specifies dual-band Wi-Fi and Gigabit Ethernet. The AiMesh expansion described requires other AiMesh-compatible ASUS routers.

View at Joybuy
TP-Link Deco XE75 tri-band mesh Wi-Fi system

TP-Link Deco XE75 tri-band mesh Wi-Fi 6E

A mesh set-up could suit you if you need Wi-Fi in several areas. Check that the connection between the access points is strong enough across your floors.

The product name specifies tri-band Wi-Fi 6E, with 2.4 GHz, 5 GHz and 6 GHz bands.

View at Joybuy

Frequently asked questions

How can you tell whether your router or internet connection is slowing down your photo uploads?

First, test using an Ethernet cable next to your router, then try Wi-Fi where you upload the photos. If the wired connection is slow too, speak to your internet provider. An extra Wi-Fi point won’t increase the speed of that connection.

Can you use a mesh system with your existing provider modem?

According to TP-Link, you can use access point mode with Deco to add Wi-Fi to an existing network. Your existing router will continue assigning addresses, but some Deco router features won’t be available in this mode. Check that the model you choose supports it.

Do you need permission from your Dutch internet provider to use your own router?

According to ACM ConsuWijzer, you have the freedom to choose your router, and providers can’t insist that you use a particular brand or model. Your router must still be suitable for your connection, and the settings you need may vary by provider. Ask your provider for these details if necessary.

What safety requirements should you consider when buying a Wi-Fi router in the Netherlands?

The Netherlands Authority for Digital Infrastructure says wireless equipment must carry the required CE marking. Wireless devices placed on the European market from 1 August 2025 must also meet applicable strengthened digital security requirements. Check the marking and update support for the specific version.

What should you consider for maintenance and power consumption?

Keep your router up to date and check how many Wi-Fi points your set-up needs. The Consumers’ Association considers power consumption in its assessments because network equipment stays on all the time. How much your set-up uses depends on the devices you choose and how you use them.