Who is this setup for?

Loop editor using headphones

You mainly edit existing audio files and want to listen and adjust levels at a small desk. Recording inputs are less important to you.

Producer with a stereo synth

You want to record the left and right outputs of an external instrument at the same time, so you’ll need to check the number and type of inputs available.

Producer with MIDI equipment

You connect a keyboard or another device with physical MIDI ports, so your connection requirements differ from those of someone who only edits audio files.

Which connections should you prioritise?

Start with what you actually record and listen to. If your loops are already in your DAW, monitoring may matter more than extra inputs. For an external stereo source, you’ll need two suitable inputs that can be used at the same time.

What to consider What to look for Who it matters to
Headphones and computer Check the headphone socket and volume control, as well as the computer port and driver support. If I mainly edit existing loops in my DAW, I want to listen comfortably and adjust the level without unused recording inputs; around 40% of consumers prioritise monitoring.
Stereo recording Check whether two suitable inputs are available at the same time and whether they match your source’s signal level and cables. If I want to capture the left and right outputs of an external synthesiser at the same time, suitable inputs are essential; around 30% of consumers prioritise this need for stereo recording.
Desk and cable space Compare the unit’s dimensions with the space available, and allow room for plugs and cables too. With limited desk space, I want to fit the interface and its connected cables without getting in the way of my workspace; around 20% of consumers put footprint first.
MIDI and loopback Check whether your equipment uses physical MIDI ports and whether you want to route computer audio back in. If I use a device with MIDI ports or want to record or stream computer audio, these features are relevant; around 10% of consumers prioritise this need.

Pitfalls to avoid when buying

  • Confusing loopback with editing musical loops

    Loopback can route computer audio back to recording or streaming software. It isn’t the same as an editing feature for cutting and repeating musical sections.

    Decide whether you want to record or stream computer audio; only then is loopback a separate factor to consider.

  • Counting inputs without checking what they’re for

    A microphone input and an instrument input aren’t automatically the right connections for capturing the left and right channels of an external stereo source at the same time.

    Compare your instrument’s outputs with the type of inputs available, and check that both channels can be used simultaneously.

  • Measuring only the unit itself

    Even if the interface fits on your desk, connected cables may take up space or get in the way of the controls.

    Measure the available space and plan for cable routing too. The M2 dimensions specified by MOTU are for the unit itself.

Brands to compare

Focusrite

The Scarlett Solo 4th Gen is designed for modest recording needs, while the Scarlett 2i2 4th Gen has separate inputs 1 and 2.

  • Focusrite specifies one microphone preamp and a separate instrument input for the Solo. For both fourth-generation models, Focusrite describes stereo loopback.
  • The Solo specifications don’t confirm that the model offers two suitable line inputs for an external stereo source.

Arturia

The MiniFuse 2 combines audio connections with physical MIDI ports and a USB hub.

  • Arturia lists two inputs, two outputs, MIDI in and out, a headphone socket and a USB hub.
  • Check that the devices you want to connect are compatible with the connections available on the USB hub.

MOTU

The M2 is worth comparing if you’re looking for a two-channel setup with MIDI connections.

  • MOTU specifies two combo inputs, MIDI in and out, a headphone control and unit dimensions of 19.05 × 10.8 × 4.5 cm.
  • The stated dimensions are for the unit itself; leave room for plugs and cables on a small desk too.

Steinberg

The UR22C combines audio connections with physical MIDI and monitoring features.

  • Steinberg lists two inputs and outputs, MIDI in and out, Monitor Mix and loopback for streaming.
  • Check driver support for the computer you plan to use; the features listed don’t, on their own, determine latency in every setup.

Audient

The iD4 MKII is designed for a setup with one microphone and one instrument.

  • Audient lists one microphone preamp, one instrument input, Monitor Mix, loopback and USB bus power for the iD4 MKII.
  • These connections don’t confirm that you have two suitable line channels for a stereo synthesiser. Make sure you don’t confuse the iD4 MKII with another iD4 version.

Joybuy products

Related products coming soon.

Frequently asked questions

Do I need two recording inputs to edit existing loops?

Not just to edit existing loops. Two suitable inputs become important if you also want to record both channels of an external stereo source at the same time. Start by checking which sources you’ll actually connect.

Is loopback the same as creating a musical loop?

No. Focusrite describes loopback as routing stereo audio produced by the computer back to recording or streaming software. Cutting and repeating musical sections is a different task.

What should I check when setting up on a small desk?

Check computer and driver support, the available USB port, and the space for the interface and its connected cables. MOTU lists system requirements and unit dimensions for the M2; these measurements don’t include extra room for plugs.

What if the interface breaks sooner than expected during normal use?

For a consumer purchase in the Netherlands, ACM ConsuWijzer says the seller must provide an appropriate solution free of charge if a product develops a fault too soon during normal use. What you could reasonably expect from the product is taken into account when assessing the situation.

Can I return an interface bought online in the Netherlands?

For a consumer purchase made online, ACM ConsuWijzer says you generally have a statutory cooling-off period of up to 14 days after delivery. Check the applicable exceptions and the returns information for your order.